Yamaha F50F Owner'S Manual Download Page 105

Page: 105 / 110

Trouble Recovery

5. Disconnect the water detection switch

coupler.

NOTICE:

Be careful not to get

any water on the water detection
switch coupler, otherwise a malfunc-
tion could occur.

[ECM01950]

6. Unscrew the filter cup from the filter

housing.

NOTICE:

Be careful not to

twist the water detection switch lead
when unscrewing the filter cup.

[ECM01960]

7. Drain the water in the filter cup by soak-

ing it up with a rag.

8. Firmly screw the filter cup onto the filter

housing.

NOTICE:

Be careful not to

twist the water detection switch lead
when screwing the filter cup onto the
filter housing.

[ECM01970]

9. Connect the water detection switch cou-

pler securely until a click is heard.

10. Fasten the water detection switch lead

with the holder.

1. Holder

1. Water detection switch coupler

ZMU07094

ZMU07096

1. Filter cup
2. Water detection switch lead

1. Water detection switch coupler

ZMU07097

ZMU07100

6C1-9-26-1E0.book 99 ページ２０１０年２月１０日　水曜日　午後１時５３分

Summary of Contents for F50F















































































































Search results

Summary of Contents for F50F

Reviews:

Related manuals for F50F

Brands by name

Popular brands

Yamaha F50F, Owner'S Manual

Search results

Summary of Contents for F50F

Reviews:

Related manuals for F50F

Brands by name

Popular brands