Yamaha F50F Owner'S Manual Download Page 104

Page: 104 / 110

Trouble Recovery

6. Drain the water in the filter cup by soak-

ing it up with a rag.

7. Firmly screw the filter cup onto the filter

housing.

NOTICE:

Be careful not to

twist the water detection switch lead
when screwing the filter cup onto the
filter housing.

[ECM01970]

8. Connect the water detection switch cou-

pler securely until a click is heard.

9. Fasten the water detection switch lead

with the plastic tie.

10. Install the top cowling.
11. Start the engine and make sure that the

water separator-alert indicator remains
off. Have a Yamaha dealer inspect the
outboard motor after returning to port.

F70A
1. Stop the engine.
2. Remove the top cowling.
3. Remove the cover.

4. Remove the holder.

1. Filter cup
2. Water detection switch lead

1. Water detection switch coupler

ZMU05477

ZMU05509

1. Plastic tie

ZMU05475

ZMU07095

6C1-9-26-1E0.book 98 ページ２０１０年２月１０日　水曜日　午後１時５３分

Summary of Contents for F50F















































































































Search results

Summary of Contents for F50F

Reviews:

Related manuals for F50F

Brands by name

Popular brands

Yamaha F50F, Owner'S Manual

Search results

Summary of Contents for F50F

Reviews:

Related manuals for F50F

Brands by name

Popular brands