Yamaha F400A Owner'S Manual Download Page 5

Page: 5 / 106

Table of contents

Cowling lock lever ............................  29
Flushing device ................................  30
Fuel filter...........................................  30

Instruments and indicators ............ 31

CL5 Display ................................... 31

Engine control system .................... 34

Alert system .................................. 34

Helm Master control system alert ....  34
Digital electronic control alert ..........  34
Overheat alert...................................  34
Low oil pressure alert .......................  35
Water separator alert........................  36

Installation ....................................... 38

Installation ..................................... 38

Mounting the outboard motor .......... 38

Operation ......................................... 40

First-time operation....................... 40

Filling engine oil................................  40
Breaking in engine............................  40
Getting to know your boat ...............  40

Checks before starting engine ...... 41

system .......................................... 45

Battery.............................................. 46

Filling fuel ..................................... 46
Operating engine........................... 47

Sending fuel ..................................... 47
Starting engine ................................. 47

Checks after starting engine ......... 52

Cooling water ................................... 52

Warming up engine....................... 52

Procedure for warming up engine.... 52

Checks after engine warm up....... 53

Shifting ............................................. 53
Stop switches................................... 53

Shifting..........................................  53
Neutral hold switch operation.......  54
Center engine switch operation....  54
Single lever switch operation........  55
Stopping boat ...............................  56
Boat direction ...............................  57
Stopping engine............................  59

Procedure for stopping engine

(6X6 switch)................................... 59

Trimming outboard motor............. 59

Adjusting trim angle (Power trim

and tilt) .......................................... 60

Adjusting boat trim ........................... 61

Tilting up and down ...................... 61

Procedure for tilting up (power trim

and tilt models) ............................. 62

Procedure for tilting down................ 64
PTT TotalTilt™.................................. 65

Shallow water .............................. 66

Cruising in shallow water ................. 66

Operating in other conditions ....... 67

Maintenance.................................... 69

Transporting and storing outboard

motor ......................................... 69

Storing outboard motor....................  69
Lubrication .......................................  69
Flushing cooling water passage.......  70
Cleaning the outboard motor ...........  71
Checking painted surface of

outboard motor ............................. 71

Periodic maintenance ................... 71

Replacement parts ...........................  71
Severe operating conditions ............  72
Maintenance chart 1.........................  73
Maintenance chart 2.........................  75
Greasing ...........................................  77
Inspecting spark plug.......................  79

U6KNK0E0.book Page 2 Monday, November 7, 2022 10:23 AM

Summary of Contents for F400A











































































































Search results

Summary of Contents for F400A

Reviews:

Related manuals for F400A

Brands by name

Popular brands

Yamaha F400A, Owner'S Manual

Search results

Summary of Contents for F400A

Reviews:

Related manuals for F400A

Brands by name

Popular brands