Yamaha F400A Owner'S Manual Download Page 95

Page: 95 / 106

Trouble Recovery

Trouble

Engine idles irregularly or stalls.

Item

Question

Answer

Spark plugs

Are spark plugs fouled or of incorrect
type?

Inspect spark plugs. Clean or replace
with recommended type.

Is spark plug gap incorrect?

Replace spark plug.

Fuel system

Is fuel system clogged?

Inspect for pinched or kinked fuel line
or other obstructions in fuel system.

Fuel

Is fuel contaminated or stale?

Fill tank with clean, fresh fuel.

Fuel filter

Is fuel filter clogged?

Clean or replace fuel filter.

Ignition parts

Are ignition parts malfunctioning?

Have serviced by a Yamaha dealer.

Alert system

Has alert system activated?

Find and correct cause of alert.

Ignition wiring

Is ignition wiring damaged or poorly
connected?

Inspect wires for breaks and wear.
Have connections tightened and bro-
ken or worn wires replaced by a
Yamaha dealer.

Engine oil

Is specified engine oil not being
used?

Inspect engine oil and replace with
specified type.

Thermostat

Is thermostat clogged or malfunc-
tioning?

Have serviced by a Yamaha dealer.

Fuel pump

Is fuel pump malfunctioning?

Have serviced by a Yamaha dealer.

Fuel tank

Is fuel tank air vent restricted or
clogged?

Remove obstruction.

Fuel joint

Is fuel joint connection incorrect?

Connect correctly.

Battery

Is battery cable disconnected?

Connect securely.

Trouble

Alert buzzer sounds or indicator lights.

Item

Question

Answer

Cooling system

Is cooling system clogged?

Inspect cooling water inlet for ob-
structions.

Low oil pressure-
alert

Is low oil pressure-alert indicator on
or blinking?

Have serviced by a Yamaha dealer.

Spark plugs

Is heat range of spark plugs incor-
rect?

Inspect spark plugs and replace with
recommended type.

Engine oil

Is specified engine oil not being
used?

Inspect engine oil and replace with
specified type.

Is engine oil contaminated or deterio-
rated?

Replace engine oil with specified ty-
pe.

Oil filter

Is oil filter clogged?

Have serviced by a Yamaha dealer.

Oil pump

Is oil pump malfunctioning?

Have serviced by a Yamaha dealer.

Thermostat

Is thermostat malfunctioning?

Have serviced by a Yamaha dealer.

Water pump

Is water pump malfunctioning?

Have serviced by a Yamaha dealer.

Fuel filter

Is there excess water in fuel filter?

Drain fuel filter.

U6KNK0E0.book Page 89 Monday, November 7, 2022 10:23 AM

Summary of Contents for F400A











































































































Search results

Summary of Contents for F400A

Reviews:

Related manuals for F400A

Brands by name

Popular brands

Yamaha F400A, Owner'S Manual

Search results

Summary of Contents for F400A

Reviews:

Related manuals for F400A

Brands by name

Popular brands