Yamaha F400A Owner'S Manual Download Page 49

Page: 49 / 106

Operation

(2) Turn the steering wheel fully to the left

and right and make sure that the out-
board motor moves to port and star-
board smoothly.

(3) Operate the throttle levers several times

to make sure there is no hesitation in
their travel.

EMU40363

Engine shut-off cord (lanyard)

Check the engine shut-off cord and clip for
damage, such as cuts, breaks, and wear.

EMU40994

Engine oil

(1) Place the outboard motor in a vertical

position (not tilted).

NOTICE:

If the out-

board motor is not level, the oil level
indicated on the oil dipstick may not
be accurate.

[ECM01862]

(2) Remove the oil dipstick and wipe it

clean.

(3) Insert the oil dipstick completely and re-

move it again.

(4) Check that the oil level on the oil dipstick

is between the upper and lower marks.
Consult your Yamaha dealer if the oil lev-
el is not at the proper level or if it appears
milky or dirty.

EMU40412

Outboard motor



Check that the outboard motor is mounted
properly and check the outboard motor
mounting bolts for looseness.



Check the propeller for damage.



Check for engine oil leaks.

1. Clip
2. Engine shut-off cord (lanyard)

ZMU06873

1. Oil dipstick

1. Oil dipstick
2. Upper mark
3. Lower mark

U6KNK0E0.book Page 43 Monday, November 7, 2022 10:23 AM

Summary of Contents for F400A











































































































Search results

Summary of Contents for F400A

Reviews:

Related manuals for F400A

Brands by name

Popular brands

Yamaha F400A, Owner'S Manual

Search results

Summary of Contents for F400A

Reviews:

Related manuals for F400A

Brands by name

Popular brands