CVP-105
11
9
Arm Assembly
9-1
Remove the top board assembly. (See Procedure 1.)
9-2
Remove the key cover assembly. (See Procedure 3.)
9-3
Remove the control panel assembly. (See Procedure 5.)
9-4
Remove the keyboard assembly. (See Procedure 8.)
9-5
Remove the five (5) screws marked [8], the five (5)
screws marked [7]. The arm assembly can then be
removed. (Fig. 12)
*
The right and left arm assembly can be removed in
the same manner.
10
PL Circuit Board
10-1
Remove the top board assembly. (See Procedure 1.)
10-2
Remove the key cover assembly. (See Procedure 3.)
10-3
Remove the control panel assembly. (See Procedure 5.)
10-4
Remove the keyboard assembly. (See Procedure 8.)
10-5
Remove the screw marked [3c]. The PL circuit
board can then be removed. (Fig. 9)
11
HP Circuit Board
11-1
Remove the four (4) screws marked [54]. The
headphone jack unit can then be removed. (Fig. 13)
11-2
Remove the two (2) hexagonal nuts marked [30].
The HP circuit board can then be removed. (Fig. 13)
12
Speakers
12-1
Disconnect the speaker cable. (Fig. 14)
12-2
Remove the eight (8) screws marked [Ba].
12-3
Place a soft blanket or similar material on the floor
near a wall, close the CVP-105 keybord cover, place
the front panel of the CVP-105 (the side of the
keyboard) on the blanket and gently lean the unit
against the wall.
Making sure that the unit can not fall. (Fig. 16)
12-4
Remove the eight (8) screws marked [Bb]. The
speaker box assembly can then be removed. (Fig. 14)
12-5
Remove the twenty (20) screws marked [27]. The SP
top board assembly can then be removed. (Fig. 15)
12-6
Remove the four (4) screws marked [26]. The right
speaker can then be removed. (Fig. 15)
*
The right and left speakers can be removed in the
same manner.
[7]: Truss Head Tapping Screw-1 3.5 x 25 MFZN2BL (EN630190)
[8]: Bind Head Tapping Screw-1 3.5 x 16 MFZN2Y (EP030190)
(Fig. 12)
<Keyboard assembly>
[8]
[8]
[7]
(Fig. 13)
<Bottom of keybed>
[54]
[30]: Hexagonal Nut 12.0 14 x 2 MFZN2BL (VB508600)
[54]: Bind Head Tapping Screw-1 3.5 x 14 MFZN2BL (EP030250)
Headphone jack unit
[30]
(Fig. 14)
Speaker box assembly
[B]: Cap screw 5.0 x 12 MFZN2BL (VS60870)
[Ba]
[Ba]
[Ba]
[Ba]
[Bb]
[Bb]
[Bb]
[Bb]
Speaker box assembly
Speaker cable
13
Front and Rear Legs
13-1
Place a soft blanket or similar material on the floor
near a wall, close the CVP-105 keybord cover, place
the front panel of the CVP-105 (the side of the
keyboard) on the blanket and gently lean the unit
against the wall.
Making sure that the unit can not fall. (Fig. 16)
13-2
Disconnect the PK cable. (Fig. 16)
13-3
Remove the twelve (12) screws marked [C]. The
rear leg can then be removed.(Fig. 16)
13-4
Remove the five (5) screws marked [D]. The front
leg can then be removed. (Fig. 17)
*
The right and left legs can be removed in the same
manner.
14
Pedal Assembly
14-1
Place a soft blanket or similar material on the floor
near a wall, close the CVP-105 keybord cover, place
the front panel of the CVP-105 (the side of the
keyboard) on the blanket and gently lean the unit
against the wall.
Making sure that the unit can not fall. (Fig. 16)
14-2
Remove the rear leg unit. (See Procedure 13-3.)
14-3
Remove the eight (8) screws marked [4]. The pedal
assembly can then be removed. (Fig. 18)
(Fig. 16)
[C]: Cap screw 5.0 x 12 MFZN2BL (VS60870)
[C] x 12
PK cable
Rear leg assembly
(Fig. 15)
[26]: Truss Head Screw 4.0 x 20 MFZN2BL (VB934000)
[27]: Truss Head Tapping Screw 5.0 x 12 MFZN2BL (VU952600)
[26]
[27] x 20
SP top board
Right speaker
(Fig. 17)
[D]: Cap screw 5.0 x 12 MFZN2BL (VS60870)
[D] x 5
Front leg assembly
[D]
(Fig. 18)
[4]: Bind Head Tapping screw-B 4.0 x 12 MFZN2BL (VR138400)
[4] x 8
[4] x 8
Front leg assembly