Yamaha Clavinova CVP-105 Service Manual Download Page 38

Page: 38 / 93

CVP-105

• HARMONIC CONTENT applies adjustment to the resonance

value that is set by the voice. This parameter specifies relative
change with the value of 64 producing 0 adjustment. As values
get higher the sound becomes increasingly eccentric. Note that
for some voices the effective parameter range is narrower than
the legal parameter range.

• RELEASE TIME applies adjustment to the envelope release

time set by the voice. This parameter specifies relative change
with the value of 64 producing 0 adjustment.

• ATTACK TIME applies adjustment to the envelope attack time

set by the voice. This parameter specifies relative change with
the value of 64 producing 0 adjustment.

• BRIGHTNESS applies adjustment to the cut-off frequency set

by the voice. This parameter specifies relative change with the
value of 64 producing 0 adjustment. Lower voices produce a
softer sound. For some voices the effective parameter range is
narrower than the legal parameter range.

3-2 CHANNEL MODE MESSAGES

STATUS

1011nnnn(BnH)

n = 0 - 15 VOICE CHANNEL NUMBER

CONTROL NUMBER

0ccccccc

c = CONTROL NUMBER

CONTROL VALUE

0vvvvvvv

v = DATA VALUE

3-2-1 ALL SOUND OFF (Receive only)

(CONTROL NUMBER = 78H , DATA VALUE = 0)

Switches off all sound from the channel. Does not reset Note On and Hold On
conditions established by Channel Messages.

3-2-2 RESET ALL CONTROLLERS (Receive only)

(CONTROL NUMBER = 79H , DATA VALUE = 0)

Resets controllers as follows.

PITCH BEND CHANGE

0 (Center)

AFTER TOUCH

0 (min.)

MODULATION

0 (min.)

EXPRESSION

127 (max.)

SUSTAIN

0 (off)

SOSTENUTO

0 (off)

SOFT PEDAL

0 (off)

NRPN

Sets number to null. (Internal data remains unchanged)

RPN

Sets number to null. (Internal data remains unchanged)

PORTAMENT CONTROL

Resets portamento source note number

PORTAMENTO

0 (off)

3-2-3 ALL NOTES OFF (Receive only)

(CONTROL NUMBER = 7BH , DATA VALUE = 0)

Switches off all of the channel’s “on” notes. However, any notes being held by
SUSTAIN or SOSTENUTO continue to sound until SUSTAIN/SOSTENUTO goes off.

3-2-4 OMNI OFF (Receive only)

(CONTROL NUMBER = 7CH , DATA VALUE = 0)

Same processing as for All Notes Off.

3-2-5 OMNI ON (Receive only)

(CONTROL NUMBER = 7DH , DATA VALUE = 0)

Same processing as for All Notes Off. Omni On is not executed.

3-2-6 MONO (Receive only)

(CONTROL NUMBER = 7EH , DATA VALUE = 0)

Same processing as for All Notes Off. If the 3rd byte is in a range of 0-16 the
corresponding channel will be changed to Mode 4 (m=1).

3-2-7 POLY (Receive only)

(CONTROL NUMBER = 7FH , DATA VALUE = 0)

Same processing as for All Sounds Off and the corresponding channel will be changed

to Mode 3.

3-3 REGISTERED PARAMETER NUMBER(RPN)

STATUS

1011nnnn(BnH)

n = 0 - 15 VOICE CHANNEL NUMBER

RPN LSB

01100100(64H)

RPN LSB NUMBER

0ppppppp

p = RPN LSB (refer to the list below)

RPN MSB

01100101(65H)

RPN MSB NUMBER

0qqqqqqq

q = RPN MSB (refer to the list below)

DATA ENTRY MSB

00000110(06H)

DATA VALUE

0mmmmmmm

m = Data Value

DATA ENTRY LSB

00100110(26H)

DATA VALUE

0lllllll

l = Data Value

First appoints the parameter for RPN MSB/LSB, then sets the parameter value for data
entry MSB/LSB.

RPN

D.ENTRY

LSB MSB MSB LSB PARAMETER NAME

DATA RANGE

00H 00H mmH -

PITCH BEND SENSITIVITY

00H-18H (0 - 24 semitones)

01H 00H mmH llH FINE TUNE

{mmH,llH} = {00H,00H}-{40H,00H}-{7FH,7FH}

(-8192*100/8192) - 0 - (+8192*100/8192)

02H 00H mmH -

COARSE TUNE

28H - 40H - 58H (-24 - 0 - +24 semitones)

7FH 7FH -

NULL

Clears the current RPN number setting. Does not change the internal parameter
settings.

3-4 NON-REGISTERED PARAMETER NUMBER(NRPN)

(Receive only)

STATUS

1011nnnn(BnH)

n = 0 - 15 VOICE CHANNEL NUMBER

NRPN LSB

01100010(62H)

NRPN LSB NUMBER 0ppppppp

p = NRPN LSB (refer to the list below)

NRPN MSB

01100011(63H)

NRPN MSB NUMBER 0qqqqqqq

q = NRPN MSB (refer to the list below)

DATA ENTRY MSB

00000110(06H)

DATA VALUE

0mmmmmmm

m = Data Value

First appoints the parameter for NRPN MSB/LSB, then sets the parameter value for
data entry MSB/LSB.

NRPN

D.ENTRY

MSB LSB MSB LSB PARAMETER NAME

DATA RANGE

01H 08H mmH —

VIBRATO RATE