Manuel_X_232_EN
10 / 13
27.01.2016
Programmable Functions
Setup Menu
Basic Menu
Function
Command
Range of Values, Comment
P0
(Parameter 0)
Teach-in zero point.
Assigning a currently
measured load to a
certain zero point.
Only executing when the car is empty.
Allowed range: -99 to 999
Suggestive range: -10 to 100
(
→ s. paragraph “Setup Menu”, “Floor Detection”)
(*) P0_
(Parameter 0 bottom)
Teach-in zero point at
lowest floor.
Assigning a currently
measured load to a
certain zero point.
Only executing when the car is empty.
Allowed range: -99 to 999
Suggestive range: -10 to 100
(
→ s. paragraph “Setup Menu”, “Floor Detection”)
(*) P0
‾
(Parameter 0 top)
Teach-in zero point at
highest floor.
Assigning a current
measured load to a
certain zero point.
Only executing when the car is empty.
Allowed range: -99 to 999
Suggestive range: -10 to 100
(
→ s. paragraph “Setup Menu”, “Floor Detection”)
(*) PE
Operating threshold for
relay contact KL3
(Car Empty)
Allowed range: -99 to 999
Suggestive range: 5..25% of nominal load
(
→ s. paragraph “Setup Menu”, “Floor Detection”)
P1
(Parameter 1)
Not used
Allowed range: -99 to 999
Suggestive range: 0 (not used)
P2
(Parameter 2)
Operating threshold for
relay contact KL1
(full load)
Allowed range: -99 to 999
Suggestive range: 100% of nominal load
P3
(Parameter 3)
Operating threshold for
relay contact KL2
(overload)
Allowed range: -99 to 999
Suggestive range: 120% of nominal load
P4
(Parameter 4)
Teach-in nominal load.
Assigning the currently
measured load to a
certain displayed value.
Only executing when the car is full.
Allowed range: -99 to 999
Suggestive range: Nominal load, i.e. real weight of
the load in kg inside the car.
(*)
Optional Parameter must be activated in the setup menu.
The switching polarity of KL3 is always inverted to the switching polarity of KL1 and KL2.
Function
Command
Range of Values, Comment
E
(Minimum load
measuring)
Activates the Parameter
PE
0
= Relay contact inactive, PE not programmable
1 = Relay contact active, PE programmable.
F
(Floor detection)
Activates the floor
detection and the
travelling cable
compensation
0
= Floor detection inactive
1 = Floor detection active, P0 must be taught-in twice
Once at lowest floor, once at highest floor.
C
(Coding)
Floor information is read
in binary or Gray code
0
= Binary coded
1 = Gray coded
L
(Logic Polarity of
coding)
Floor information and
Synch is low or high
active
0
= 5..24V corresponds logic 1 (1 active)
1 = 0V corresponds logic 1 (0 active)
S
(External sensor for
“Car
Empty
”)
Activates sensor at X5
(
→ s. paragraph “Input
and Output“)
0
= Breaker signal is not processed
1 = Breaker signal is processed
(
→ s. paragraph “External Sensor”)
P
(Polarity of the switching
output X1 and relay at
X3)
Inverts the polarity of the
digital switching outputs
X1 and the relay at X3
0
= normal polarity, achieved operating threshold
sets output to plus, relay energizes.
1 = inverted polarity, achieved operating threshold
sets output to 0V, relay de-energizes.
I
(Polarity load measuring
sensor at X2)
Inverts the polarity of the
signals of the load
measuring sensor at X2
0
= normal polarity, sensor signal becomes more
positive during loading of the car
1= inverted polarity, sensor signal becomes more
negative during loading of the car
A
(Response delay of
KL 2)
Delays the operating of
KL2 (overload) during
programmed time
Adjustable from 99 Digits, relative 0 to 9.9 seconds.
Recommended value: 1 second (10 Digits)
H
(Switching hysteresis for
all outputs)
Switching hysteresis in
kg for all outputs.
Adjustable from 0..99kg.
Recommended value: 10..15kg.
Prevents the
“oscillating“ of the relay contacts.
(
→ consult the paragraph "Troubleshooting“)
Please note!
If the functions (E, F, P, I) are modified in the setup menu, so P0 und P4 must be compulsory taught-in again.
This signifies the car must be load with the nominal load again.
The blinking of the left zero point warns you that a new teach-in is required.
If the change is manually undone in the setup menu, so another teach-
in won’t be required.
But this isn’t possible anymore when you have left the setup menu before without undoing the change.
Default settings
of the setup menu are marked
bold
in the list above.
