manualshive.com logo in svg

XONTEL XonTel XT- 60 PBX, Administrator'S Manual

Share
Download
XONTEL XonTel XT- 60 PBX Administrator'S Manual Download Page 42

42 

 

 

 

 

Trunks 

XT-60/XT-120 supports FXO trunk, BRI trunk, GSM/3G trunk and VoIP trunk. In this chapter, we give 

a simplified guide of setting up trunks. 

FXO Trunk 

BRI Trunk 

GSM/3G Trunk 

VoIP Trunk

 

 

FXO Trunk

 

FXO trunk is also known as PSTN trunk. The public switched telephone network (PSTN) is the 

network of the world's public circuit-switched telephone networks. 

 

To extend FXO trunk on the system, you need to insert FXO module to PBX. Go to 

Settings > PBX 

> Trunks 

to edit the FXO trunk. Before configuring a FXO trunk, please make sure that the analog 

line is connected to XonTel XT-60/XT-120 FXO port. 

 

Click  

  

to edit the FXO trunk. Please check the FXO trunk configuration parameters below. 

 

1)  Basic Settings 

 

General

 

Trunk Name 

Give this trunk a name to help you identify this trunk. 

Rx Volume 

Set the receiving volume of FXO port or choose Custom to define the RX gain 
below. 

RxGain 

The RX Gain for the receiving channel of FXO Port. The valid range is -30db 

to 12db. 

Tx Volume 

Set the transmitting volume of FXO port or choose Custom to define the TX 

gain below. 

TxGain 

The TX Gain for the transmitting channel of FXO Port. The valid range is -30db 

to 12db. 

Enable SLA 

If enabled, this trunk will not be available in routes or other channels. 

Allow Barge 

Whether to allow other SLA stations to join a call by pressing the SLA key. 

 

 

Hold Access 

Specify hold permission for the station. 

 

Open: 

other stations that share the same line could retrieve the call. 

 

Private: 

the call can be retrieved only by the station that previously put the 

call on hold, not by others sharing the same line. 

Table 5-1 FXO Trunk Configuration Parameters 

– Basic 

 

2)  Hangup Detection 

Hangup detection settings help the system to detect if a call is hung up. If you find the PSTN call 

Summary of Contents for XonTel XT- 60 PBX






















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands