XONTEL XonTel XT- 60 PBX Administrator'S Manual Download Page 10

Page: 10 / 117

Port Description

Ports

Description

RJ11 Port

FXO port

(red light): for the connection of PSTN lines or FXS ports of traditional

PBX.

FXS port

(green light): for the connection of analog phones.

BRI port

(orange light): for the connection of ISDN BRI lines.

Note:

the sequence number of the ports corresponds to that of the Indicator

lights in the front panel. (I.e. the LED lights in the front indicate the connection

status of the corresponding ports at the front panel.)

ANT

Connect to GSM/3G Antenna.

TF Slot

Insert TF card.

SD Slot

Insert SD card.

Ethernet Port

XonTel XT-60/XT-120 supports two 10/100/1000M Ethernet ports. There are 2

Ethernet

modes for the system. The default mode is “Bridge”.

Bridge:

LAN port interface will be used for uplink connection. WAN port

interface will be used as bridge for PC connection.

Dual:

both ports can be used for uplink connection.

Reset Button

Press and hold for 10 seconds to restore the factory defaults

Power Inlet

Connect the supplied power supply to the port.

Power Switch

Press this button to switch on/off the device.

Summary of Contents for XonTel XT- 60 PBX






















































































































Search results

Summary of Contents for XonTel XT- 60 PBX

Reviews:

Brands by name

Popular brands

XONTEL XonTel XT- 60 PBX, Administrator'S Manual

Search results

Summary of Contents for XonTel XT- 60 PBX

Reviews:

Brands by name

Popular brands