XONTEL S2400 User Manual Download

Page: 95 / 104

S2400 User Manual



Extension is idle



Extension is ringing



Extension is busy



Extension is on hold

Voicemail

Display message status of the extension.

Format: New/Old

Example: 1/3

Description: There are 1 new voice message, and 3 old messages.

Trunk Status

Users could check all the PSTN trunks status and VoIP trunk status if VoIP trunk is

created.

Figure 19-2 Trunk Status

Table 19-2 VoIP Trunk Status

Table 19-3 PSTN Trunk Status

Up/Down

Status for CO lines:



: the CO line works well.

Domain Name/IP

Display the domain name/IP for the VoIP trunk.



[IP]:[Port]

: display the IP address of the VoIP service

provider and the SIP registry port.

Example: 110.92.83.4:5060

Description: the extension is registered on IP

192.168.6.142 and the SIP port is 5060.

Provider Name

Display the trunk name.

(VoIP) Status

VoIP trunk status:



Registered

: successful registration, trunk is ready for

use.



Unreachable

: cannot reach the VoIP service provider.



Failed

: trunk registry failed.

Summary of Contents for S2400









































































































Search results

Summary of Contents for S2400

Reviews:

Related manuals for S2400

Brands by name

Popular brands

XONTEL S2400, User Manual

Search results

Summary of Contents for S2400

Reviews:

Related manuals for S2400

Brands by name

Popular brands