XONTEL S2400 User Manual Download

Page: 16 / 104

S2400 User Manual

Making and Receiving Calls

S2400 is ready to play out of the box with plug-and-play facility. Power on the device

and connect analog phones and CO lines, you can make internal calls, outbound calls

and inbound calls with S2400.

Note:

To custom the configurations according to your situation, you have to connect the

network cable to S2400, then log in the web user interface to change the settings.

□

Internal calls between extensions

Connect analog phones to FXS ports on S2400, users could make calls between
extensions just by dialing the other’s extension number. If IP terminals have
registered to S2400 successfully, users could also make internal calls using SIP

extensions.

Default FXS extension number: 601-624.

□

Outbound calls

Firstly, please connect CO lines to CO ports on S2400. Then the default

extensions are able to seize an available CO line to make outbound calls. Users

could dial digit 9 to seize a CO line first, and dial the external number after

hearing a dial tone.

Users could also use the default outgoing rule to make outbound calls. The dial

pattern of the default outbound route is

―8.‖and strip 1 digit, users should dial digit

8 before the number.

□

Inbound calls

When the user calls the trunk number of the CO lines, S2400 would route the call

to the analog phone which is connected to the port EXT1.

Summary of Contents for S2400









































































































Search results

Summary of Contents for S2400

Reviews:

Related manuals for S2400

Brands by name

Popular brands

XONTEL S2400, User Manual

Search results

Summary of Contents for S2400

Reviews:

Related manuals for S2400

Brands by name

Popular brands