XONTEL S2400 User Manual Download Page 84

Page: 84 / 104

S2400 User Manual

Input the Net-Disk information in

―Connect to Network Disk‖ tab.

Figure 16-4 Connect to Network Disk

Table 16-2 Network Disk Settings

If the configuration is correct, you will see the Network Disk information.

Figure 16-5 Network Disk Status

Share Recordings

Users could share recordings on the network. This setting is only applied to the Call

Recording folder in the SD Card. Go to

System→ Storage Management→ Network

Disk Settings

to configure the sharing settings.

Network Disk Settings

Running Status

Shows if the Net-Disk is successfully mounted to S2400.

Enable



Yes: Enable Network Disk



No: Disable Network Disk

Net-Disk Host/IP

Set the IP address where the recordings will be stored.

Net-Disk Share Name

The shared folder name where the recordings will be

stored.

Net-Disk Access User Name

The User name used to log in the Network share. Leave

this blank if it is not required. In general, you use the

administrator account on PC as a user name here.

Net-Disk Access Password

The password used to log into the network share.

Leave this blank if it is not required.

Summary of Contents for S2400









































































































Search results

Summary of Contents for S2400

Reviews:

Related manuals for S2400

Brands by name

Popular brands

XONTEL S2400, User Manual

Search results

Summary of Contents for S2400

Reviews:

Related manuals for S2400

Brands by name

Popular brands