XONTEL S2400 User Manual Download Page 8

Page: 8 / 104

S2400 User Manual

S2400 Rear Panel

Figure 1-2 S2400 Rear Panel

Table 1-3 S2400 Rear Panels

–Port Description

Port

Description

RJ21 CO Ports

For connection of CO lines with an RJ21 to RJ11 cable.

RJ21 FXS Ports

For connection of analog phones/fax machines with an RJ21 to

RJ11 cable.

SD Card Slot

Insert the SD card and restore the recording files.

LAN Port

10/100 Base-TX, connect one end of an RJ-45 Ethernet cable

into the LAN port.

Console Port

Used for service and maintenance.

Reset Button

Press the reset button to restore the factory defaults.

Please make sure that you want to reset, because once

reset

the

configurations would

erased

automatically.

Power Switch

Power Inlet

For connection of power supply.

Table 1-4 S2400 Rear Panel

–LED Description

LED

LED Status

Description

POWER

The power is switched on.

Off

The power is switched off.

RUN

Blinking

S2400 is running properly.

Not Blinking/Off

S2400 goes wrong.

Summary of Contents for S2400









































































































Search results

Summary of Contents for S2400

Reviews:

Related manuals for S2400

Brands by name

Popular brands

XONTEL S2400, User Manual

Search results

Summary of Contents for S2400

Reviews:

Related manuals for S2400

Brands by name

Popular brands