XONTEL S2400 User Manual Download

Page: 102 / 104

S2400 User Manual

Backup and Restore

S2400 provides Backup and Restore feature, which allows you to create a complete

backup of S2400 configurations to a file.

Notes:

1. The backup file only covers the configurations but not the CDR, voicemail and call

recordings.

2. When you have updated the firmware version,

it’s not recommended to restore

using old package.

3. Backup from an earlier version cannot be restored on S2400 of a later version.



Create a New Backup

Click

to create a new backup.



Upload a Backup

Click

to upload a backup.



Restore

To restore S2400 configuration data, upload the backup file to S2400 and

Reboot the system to take effect.

Please note the current configurations will be OVERWRITTEN with the backup

data.

Figure 20-6 Restore Backup

Reset and Reboot

Users could reset and reboot the system under

System→ System Preferences→

Reset and Reboot

Summary of Contents for S2400









































































































Search results

Summary of Contents for S2400

Reviews:

Related manuals for S2400

Brands by name

Popular brands

XONTEL S2400, User Manual

Search results

Summary of Contents for S2400

Reviews:

Related manuals for S2400

Brands by name

Popular brands