manualshive.com logo in svg

XLT Ovens 1832, Parts & Service Manual

Share
Download
XLT Ovens 1832 Parts & Service Manual Download Page 5

Technical Support  US:  888-443-2751 

Technical Support  INTL:  316-943-2751 

 

5 

Warning & Safety Information........................................................................................................... 2 
General ............................................................................................................................................... 6 
Warranty ............................................................................................................................................. 8 
Installation Responsibilities ............................................................................................................. 10 
Oven Theory of Operation ............................................................................................................... 12 
Hood Theory of Operation ............................................................................................................... 20 
Oven Troubleshooting ...................................................................................................................... 26 
Hood Troubleshooting ...................................................................................................................... 28 
Oven Service Procedures.................................................................................................................. 30 
Hood Service Procedures ................................................................................................................. 38 
Parts Ordering................................................................................................................................... 40 
Oven Parts ........................................................................................................................................ 41 
Hood Parts ........................................................................................................................................ 73 
Electrical Schematics .....................................................................................................................  . 76 
Notes ...............................................................................................................................................  . 93 

TABLE OF CONTENTS 

For maintenance procedures, please refer to the XLT Installation & Operation Manual. 

Summary of Contents for 1832































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands