manualshive.com logo in svg

XLT Ovens 1832, Parts & Service Manual

Share
Download
XLT Ovens 1832 Parts & Service Manual Download Page 22

Technical Support  US:  888-443-2751 

Technical Support  INTL:  316-943-2751 

 

22 

HOOD THEORY OF OPERATION (STD W/FS) 

HUI

 - Hood User Interface contains the factory settings so that the hood will operate with the cor-

rect hertz when the correct oven size and number of ovens are selected. The  factory settings also 
contain a selection for a VFD, Non VFD, type of MUA activation, and for a World installation. A 
beeping sound and the display will flash if an alarm occurs. An error message will display at top of 
screen on HUI. Touching the “I” button will give a brief description of how to correct the error. 
Touching the “Light Bulb” button will turn the light on and off inside the hood. 

 

Touching the “Silver Square” buttons will turn each oven on or off and sequence the operation of 
the VFD and the MUA circuits. RS-485 cable supplies power and communication between the 
HUI and HMC. 

LT1 & LT2

 - These are light bulbs at each end of the hood that illuminate when the HUI hood 

lights button is pressed. When pressed again the lights turns off.

 

M1 

- The Exhaust Fan Motor is a 3-phase, direct drive motor.  In normal operation, it is powered 

by the VFD and its RPM will vary as the frequency from the VFD varies. There are no user ser-
viceable parts in the motor, and the bearings are permanently lubricated. 

M2 & M3 

- The Cooling Fan Motor is a 24 VDC, direct drive motor.  In normal operation, it is 

powered through HMC.  These fans are used to keep the control box for the hood cool.  There are 
no user serviceable parts in the motor, and the bearings are permanently lubricated. 

PLUG 1, 2, & 3 

- These are circular electrical plugs on one end of the SRC.  The plugs connect to 

Receptacles 4, 5, & 6 on the back of the hood.  The other end of the SRC plugs into the oven wire 
harness, and eliminates the power button supplied on the oven.  Conversely, when the HUI on the 
hood is turned off, the corresponding oven is turned off as well. 

XLT Logo 

Hood Lights 

Alarm Mute 

Error Information 

Oven Off (Outline) 

Oven On (Filled) 

Exhaust Fan On 

Exhaust Fan Speed 

Oven Buttons 

Summary of Contents for 1832































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands