Xinje VB3, User Manual

Page: 92 / 107

V5 series inverter
86
0 0 0 0
：
Disabled Disabled Disabled Disabled
1 1 1 1
：
Enabled Enabled Enabled Enabled
Unit Unit Unit Unit’’’’ssss place place place place of of of of LED LED LED LED
：
start mode
0 0 0 0
：
Auto Auto Auto Auto mode mode mode mode.... The inverter will running at preset frequency (P9.02) for certain time (P9.03), and then enter the traverse
operation.
1 1 1 1
：
Manual Manual Manual Manual mode mode mode mode.... If the multi-function terminal (Xi is set to No.25 function) is enabled, the inverter will enter traverse
mode. If the terminal is disabled, the drive will end traverse operation and operate at the pre-traverse frequency (P9.02).
Ten Ten Ten Ten’’’’ssss place place place place of of of of LED LED LED LED
：
Traverse operating amplitude
0 0 0 0
：
Variable Variable Variable Variable amplitude amplitude amplitude amplitude.... Traverse operating amplitude AW changes with the central frequency and the change rate is defined
by P9.04.
1
1
1 1
：
Fixed
Fixed
Fixed Fixed amplitude
amplitude
amplitude amplitude.... Traverse operating amplitude AW is decided by max frequency and P9.04.
P9.02 is used to set running frequency before inverter enter traverse state.
If you select auto start mode, P9.03 is used to set the holding time with pre-traverse frequency before the inverter enter
traverse state; if you select manual start mode
，
P9.03 is disabled. Refer to Fig. 4
－
45 for introduction.
Variable amplitude
：
Aw
＝
Central frequency
×
P9.04
Fixed amplitude
：
Aw
＝
Max operting frequency P0.06
×
P9.04
Prompt
：
The traverse frequency will be limit by upper/lower limit of frequency, and the traverse operation will not work
abnormally with unsuitable setup.
As shown in Fig4-45, there is no jitter frequency if P9.05 is set to 0.
It defines the time of a complete traverse operation cycle including rising and falling processes.
Running time of traverse rising stage
＝
P9.06
×
P9.07(s)
，
Time of falling stage
＝
P9.06
×（
1
－
P9.07
）
(s)
。
Refer Fig.4
－
45
for introduction
Note
Note Note
Note
：
You can select S-curve Acc/Dec mode along with traverse so as to make the traverse operating more smoothly.
This group of parameters are used for fixed length control.
The drive inputs counting pulses via terminals (X6, defined as function 35), and calculate length according to the number of
pulses per revolution (P9.13) and perimeter of shaft (P9.12).
Calculated length
＝
Number of pulses
÷
number of pulses per revolution
×
perimeter of shaft
P9.00 P9.00 P9.00 P9.00 Traverse Traverse Traverse Traverse operation operation operation operation selection selection selection selection Range Range Range Range
：
0 0 0 0,,,, 1 1 1 1 0 0 0 0
P9.01 P9.01 P9.01 P9.01 Traverse Traverse Traverse Traverse operation operation operation operation control control control control mode mode mode mode Range Range Range Range
：
00 00 00 00
～
11 11 11 11 0 0 0 0
P9.02 P9.02 P9.02 P9.02 Pre-traverse Pre-traverse Pre-traverse Pre-traverse frequency frequency frequency frequency Range Range Range Range
：
0.00 0.00 0.00 0.00
－
650.00Hz 650.00Hz 650.00Hz 650.00Hz 0.00Hz 0.00Hz 0.00Hz 0.00Hz
P9.03 P9.03 P9.03 P9.03 Waiting Waiting Waiting Waiting time time time time before before before before pre-traverse pre-traverse pre-traverse pre-traverse frequency frequency frequency frequency Range Range Range Range
：
0.0 0.0 0.0 0.0
－
6000.0s 6000.0s 6000.0s 6000.0s 0.0s 0.0s 0.0s 0.0s
P9.04 P9.04 P9.04 P9.04 Traverse operating amplitude Range Range Range Range
：
0.0 0.0 0.0 0.0
～
50.0 50.0 50.0 50.0
％
0.0 0.0 0.0 0.0
％
P9.05 P9.05 P9.05 P9.05 Jitter Jitter Jitter Jitter frequency frequency frequency frequency Range Range Range Range
：
0.0 0.0 0.0 0.0
～
50.0 50.0 50.0 50.0
％
0.0 0.0 0.0 0.0
％
P9.06 P9.06 P9.06 P9.06 Traverse Traverse Traverse Traverse operating operating operating operating cycle cycle cycle cycle Range Range Range Range
：
0.1 0.1 0.1 0.1
～
999.9s 999.9s 999.9s 999.9s 10.0s 10.0s 10.0s 10.0s
P9.07
P9.07 P9.07
P9.07 Rising time of trangle wave Range
Range Range
Range
：
0.0
0.0 0.0
0.0
～
98.0
98.0 98.0
98.0
％
50.0
50.0 50.0
50.0
％
P9.08 P9.08 P9.08 P9.08 Reference Reference Reference Reference length length length length Range Range Range Range
：
0.000 0.000 0.000 0.000
～
65.535km 65.535km 65.535km 65.535km 0.000(km) 0.000(km) 0.000(km) 0.000(km)
P9.09 P9.09 P9.09 P9.09 Actual Actual Actual Actual length length length length
Range
Range Range
Range
：
0.000
0.000 0.000
0.000
～
65.535km
65.535km 65.535km
65.535km
0.000(km) 0.000(km) 0.000(km) 0.000(km)
P9.10 P9.10 P9.10 P9.10 Times Times Times Times of of of of length length length length Range Range Range Range
：
0.001 0.001 0.001 0.001
～
30.000 30.000 30.000 30.000 1.000 1.000 1.000 1.000
P9.11 P9.11 P9.11 P9.11
correction correction correction correction coefficient coefficient coefficient coefficient of of of of
length length length length
Range Range Range Range
：
0.001 0.001 0.001 0.001
～
1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000
P9.12
P9.12 P9.12
P9.12 Perimeter
Perimeter Perimeter
Perimeter of
of of
of shaft
shaft shaft
shaft Range
Range Range
Range
：
0.01
0.01 0.01
0.01
～
100.00(cm)
100.00(cm) 100.00(cm)
100.00(cm) 10.00(cm)
10.00(cm) 10.00(cm)
10.00(cm)
P9.13 P9.13 P9.13 P9.13 Number Number Number Number of of of of pulses pulses pulses pulses per per per per revolution revolution revolution revolution Range Range Range Range
：
1 1 1 1
～
9999 9999 9999 9999 1 1 1 1
All manuals and user guides at all-guides.com