Xinje VB3, User Manual

Page: 76 / 107

V5 series inverter
70
12 12 12 12:::: DC DC DC DC injection injection injection injection braking braking braking braking command command command command DB DB DB DB,,,, the terminal can be used to perform DC injection braking to the motor that is running
so as to realize the emergent stop and accurate location of the motor. Initial braking frequency, braking time and braking current
are defined by P2.06~P2.08. Braking time is the greater value between P2.07 and the effective continuous time defined by this
control terminal.
1 1 1 13 3 3 3
：
Inverter Inverter Inverter Inverter running running running running prohibit prohibit prohibit prohibit.... When the terminal is enabled, the inverter that is operating will coast to stop and it is prohibited
to restart. This function is mainly used in application with requirements of safety protection.
14 14 14 14~ ~ ~ ~15 15 15 15:::: Frequency Frequency Frequency Frequency ramp ramp ramp ramp up up up up ((((UP UP UP UP)/Frequency )/Frequency )/Frequency )/Frequency ramp ramp ramp ramp down(DOW down(DOW down(DOW down(DOWN N N N)))) The terminal can be used to increase or decrease the
frequency. Its function is the same with operating keys on the panel, which enables remote control. This terminal is enabled
when P0.01=3. Increase or decrease rate is determined by P4.09.
16 16 16 16:::: Acc/Dec Acc/Dec Acc/Dec Acc/Dec prohibit prohibit prohibit prohibit.... The terminal can make the motor operate at present speed without being influenced by external
signal (except stopping command).
Note
Note
Note Note:::: Disabled in normal dec-to-stop.
17
17
17 17:::: Reset
Reset
Reset Reset signal
signal
signal signal.... The inverter can be reset via this terminal when the inverter has a fault. The function of this terminal is the same
with that of on the panel.
18 18 18 18:::: External External External External fault fault fault fault signal signal signal signal normally normally normally normally open open open open input input input input.... The fault signal of external equipment can be input via the terminal, which
is convenient for the inverter to monitor the external equipment. Once the inverter receives the fault signal, it will display
“E-13”. Refer to Fig.4-20.
19
19 19
19~
~ ~
~21
21 21
21:::: Frequency
Frequency Frequency
Frequency selector
selector selector
selector 1
1 1
1....
Different ON/OFF combination of terminals 19, 20 and 21 can select reference frequency as
shown in Table 4-4. The inverter will be active this function and P0.01 later.
Table
Table Table
Table 4-4
4-4 4-4
4-4 Frequency
Frequency Frequency
Frequency selector
selector selector
selector
22
22 22
22
：
Terminal
Terminal Terminal
Terminal control
control control
control mode
mode mode
mode is
is is
is forcibly
forcibly forcibly
forcibly enabled
enabled enabled
enabled.... When this terminal is enabled, the running mode will be turn to terminal
control.
23
23 23
23
～
24
24 24
24:::: Control
Control Control
Control mode
mode mode
mode selection.
selection. selection.
selection.
Control mode can be selected via ON/OFF combination of terminals.The inverter will be
active this function and P0.03 later.
Table
Table Table
Table 4-5
4-5 4-5
4-5 Control
Control Control
Control mode
mode mode
mode
25 25 25 25
：
Start Start Start Start traverse traverse traverse traverse operation. operation. operation. operation. When the traverse operation is as “manual”, the traverse function will be enabled if this
terminal is enabled, see Group P9 for details.
26 26 26 26
：
Res Res Res Reseeeetttt traverse traverse traverse traverse operation operation operation operation.... No matter the traverse operation is “Manual” or “Auto”, close-loop this terminal will clear
all the memorized information of traverse operation. Disconncet this terminal can restart traverse operation. Refer to P9 for
parameters instruction.
27 27 27 27
：
Close-loop Close-loop Close-loop Close-loop disabled disabled disabled disabled.... The terminal can be used to flexible switching the close-loop operation and low level operation,
Frequency Frequency Frequency Frequency selector selector selector selector 3 3 3 3 Frequency Frequency Frequency Frequency selector selector selector selector 2 2 2 2 Frequency Frequency Frequency Frequency selector selector selector selector 1 1 1 1 Frequency
Frequency
Frequency Frequency selector
selector
selector selector
OFF OFF OFF Hold the setting
OFF OFF ON Digital setting
OFF ON OFF Terminal UP/DOWN setting
OFF ON ON Serial port setting
ON OFF OFF VI
ON OFF ON CI
ON ON OFF PULSE
ON ON ON
Combination setting
(refer to P3.01)
Terminal Terminal Terminal Terminal 2 2 2 2 Terminal Terminal Terminal Terminal 1 1 1 1 Control Control Control Control mode mode mode mode
OFF OFF Hold the control mode
OFF ON Panel control mode
ON OFF Terminal control mode
ON ON Serial port control mode
All manuals and user guides at all-guides.com
all-guides.com