manualshive.com logo in svg

Xilinx SelectIO 7 Series, User Manual

The Xilinx SelectIO 7 Series is a highly versatile product offering cutting-edge I/O capabilities. Unlock its full potential by accessing the comprehensive user manual, available for free download at manualshive.com. This essential manual provides detailed insights and instructions to maximize the utilization of this powerful hardware.

Share
Download
background image

7 Series FPGAs SelectIO Resources User Guide

www.xilinx.com

13

UG471 (v1.10) May 8, 2018

Chapter 1

SelectIO Resources

I/O Tile Overview

Input/output characteristics and logic resources are covered in three consecutive chapters.

Chapter 1, SelectIO Resources

 describes the electrical behavior of the output drivers and 

input receivers, and gives detailed examples of many standard interfaces. 

Chapter 2, 

SelectIO Logic Resources

 describes the input and output data registers and their 

double-data rate (DDR) operation, and the programmable input delay (IDELAY) and 
programmable output delay (ODELAY). 

Chapter 3, Advanced SelectIO Logic Resources

 

describes the data serializer/deserializer (SERDES).

The 7 series FPGAs offer both high-performance (HP) and high-range (HR) I/O banks. The 
HP I/O banks are designed to meet the performance requirements of high-speed memory 
and other chip-to-chip interfaces with voltages up to 1.8V. The HR I/O banks are designed 
to support a wider range of I/O standards with voltages up to 3.3V. 

Table 1-1

 highlights 

the features supported in the HP and HR I/O banks. Refer to 

Table 1-1

 for help when 

making initial decisions on I/O banks for a particular design's requirements. See the 
specific device family data sheet for details on the performance and other electrical 
requirements of the HP and HR I/O banks.

The 7 series FPGAs contain different combinations of HR and HP I/O banks. The 

7 Series 

FPGAs Overview

 documents the available number of each type of bank for all devices.

Table 1-1:

Supported Features in the HR and HP I/O Banks

Feature

HP I/O Banks

HR I/O Banks

3.3V I/O standards

(1)

N/A

Supported

2.5V I/O standards

(1)

N/A

Supported

1.8V I/O standards

(1)

Supported

Supported

1.5V I/O standards

(1)

Supported

Supported

1.35V I/O standards

(1)

Supported

Supported

1.2V I/O standards

(1)

Supported

Supported

LVDS signaling

Supported

(2)

Supported

24 mA drive option for LVCMOS18 and LVTTL outputs

N/A

Supported

V

CCAUX_IO

 supply rail

Supported

N/A

Digitally-controlled impedance (DCI) and DCI cascading

Supported

N/A

Internal V

REF

Supported

Supported

Send Feedback

Summary of Contents for SelectIO 7 Series





























































































































































































Reviews:

No comments

Related manuals for SelectIO 7 Series

Paradyne 3163 Quick Reference preview
3163
Brand: Paradyne Pages: 16
Dave Embedded Systems ARM Cortex-A9 MPCore Quick Start Manual preview
ARM Cortex-A9 MPCore
Brand: Dave Embedded Systems Pages: 67
dbx Zone Pro 640 Manual preview
Zone Pro 640
Brand: dbx Pages: 2
dbx 166 Quick Start Manual preview
166
Brand: dbx Pages: 17
Mylex eXtremeRAID 1100 Installation Manual preview
eXtremeRAID 1100
Brand: Mylex Pages: 74
RAK RAK3372 Quick Start Manual preview
RAK3372
Brand: RAK Pages: 30
Avaya XM24 Expansion Module Installation Instructions preview
XM24 Expansion Module
Brand: Avaya Pages: 5
Daedalon EC-33 Instruction Manual preview
EC-33
Brand: Daedalon Pages: 6
Balluff Easy Tool-ID BSG TID-05-T30-00-005 Installation And Operation Manual preview
Easy Tool-ID BSG TID-05-T30-00-005
Brand: Balluff Pages: 46
MEMON memonizerWORKSTATION Quick Start Manual preview
memonizerWORKSTATION
Brand: MEMON Pages: 2
Digi 9P 9360/9750 User Manual preview
9P 9360/9750
Brand: Digi Pages: 75
Optus Ultra WiFi Booster Quick Manual preview
Ultra WiFi Booster
Brand: Optus Pages: 8
Cypress Semiconductor CY7C1441AV33 Specification Sheet preview
CY7C1441AV33
Brand: Cypress Semiconductor Pages: 31
Paradyne SLV Installation Instructions Manual preview
SLV
Brand: Paradyne Pages: 28
Adaptec ASR-3085 Important Information About Issues And Errata preview
ASR-3085
Brand: Adaptec Pages: 3
Spectrum Digital XDS510USB Installation Manual preview
XDS510USB
Brand: Spectrum Digital Pages: 11
IEI Technology IMBA-C604EP User Manual preview
IMBA-C604EP
Brand: IEI Technology Pages: 213
Acnodes RK 1016B User Manual preview
RK 1016B
Brand: Acnodes Pages: 10

Brands by name

Popular brands

Load more brands