Xilinx SelectIO 7 Series User Manual Download Page 29

Page: 29 / 188

7 Series FPGAs SelectIO Resources User Guide

www.xilinx.com

UG471 (v1.10) May 8, 2018

7 Series FPGA DCI—Only available in the HP I/O banks

The I/O standards with split-termination DCI resistors that are always present are shown
in

Table 1-3

The I/O standards with split-termination DCI (T_DCI) that are only enabled when 3-stated
are shown in

Table 1-4

Note:

The T_DCI standards can only be assigned to bidirectional pins.

DCI in 7 Series FPGAs I/O Standards

DCI supports the standards shown in

Table 1-5

Table 1-3:

I/O Standards with Split-Termination DCI Always Present

DIFF_HSTL_I_DCI

HSTL_I_DCI_18

SSTL18_II_DCI

DIFF_SSTL18_II_DCI

HSTL_II_DCI

DIFF_HSTL_II_DCI

SSTL15_DCI

(1)

DIFF_SSTL15_DCI

(1)

HSTL_II_DCI_18

DIFF_HSTL_II_DCI_18

SSTL135_DCI

DIFF_SSTL135_DCI

DIFF_SSTL12_DCI

Notes:

1. The non-class II versions of the HSTL and SSTL I/O standards only have the split-termination DCI resistors present on inputs, not

outputs. Bidirectional pin assignments are not allowed for these standards.

Table 1-4:

I/O Standards with Split-Termination DCI Only When 3-Stated

HSTL_II_T_DCI

SSTL18_II_T_DCI

DIFF_SSTL18_II_

T_DCI

HSTL_II_T_DCI_18

SSTL15_T_DCI DIFF_SSTL15_T_DCI

DIFF_HSTL_II__T_DCI

SSTL135_T_DCI

DIFF_SSTL135_T_DCI

DIFF_HSTL_II_T_DCI_18

SSTL12_

T_DCI

DIFF_SSTL12_T_DCI

Table 1-5:

All 7 Series Device DCI I/O Standards

LVDCI_18

HSTL_I_DCI

DIFF_HSTL_I_DCI

SSTL18_I_DCI

DIFF_SSTL18_I_DCI

LVDCI_15

HSTL_I_DCI_18

DIFF_HSTL_I_DCI_18

SSTL18_II_DCI

DIFF_SSTL18_II_DCI

LVDCI_DV2_18

HSTL_II_DCI

DIFF_HSTL_II_DCI

SSTL18_II_T_DCI

DIFF_SSTL18_II_T_DCI

LVDCI_DV2_15

HSTL_II_DCI_18

DIFF_HSTL_II_DCI_18

SSTL15_DCI

DIFF_SSTL15_DCI

HSLVDCI_18

HSTL_II_T_DCI

DIFF_HSTL_II_T_DCI SSTL15_T_DCI

DIFF_SSTL15_T_DCI

HSLVDCI_15

HSTL_II_T_DCI_18

DIFF_HSTL_II_T_DCI_18

SSTL135_DCI

DIFF_SSTL135_DCI

SSTL135_T_DCI DIFF_SSTL135_T_DCI

SSTL12_DCI DIFF_SSTL12_DCI

SSTL12_T_DCI DIFF_SSTL12_T_DCI

HSUL_12_DCI

DIFF_HSUL_12_DCI

Send Feedback

Summary of Contents for SelectIO 7 Series





























































































































































































Search results

Summary of Contents for SelectIO 7 Series

Reviews:

Related manuals for SelectIO 7 Series

Brands by name

Popular brands

Xilinx SelectIO 7 Series, User Manual

Search results

Summary of Contents for SelectIO 7 Series

Reviews:

Related manuals for SelectIO 7 Series

Brands by name

Popular brands