Xerox WORKCENTRE 5030 Quick Reference Manual Download Page 182

Page: 182 / 186

Page 11-10

Quick Reference Guide

Jobs scan but do not print

Some jobs require image processing before printing. This may take as long as 2
seconds per page.

Check the

Job Status

queue to determine if a job is processing. There may be a

job in the queue with a status of paused. Delete this job if it remains in the state
over 3 minutes.

This may possibly be a result of an incorrect feature combination. The software
may need to be reset. Contact your System Administrator.

Output does not reflect the selections made on the
Touch Screen

Press

Clear All

between jobs.

If a

Save

button displays on the touch screen, ensure

Save

is selected after

each selection.

Fault Messages will not clear

There may be occasions when a fault is cleared but the message will not clear.
Reboot your machine by powering OFF and ON using the ON/OFF switch at the
side of the machine.

CAUTION: Wait approximately 20 seconds before turning the machine back
ON. Any incomplete jobs in the queue will be lost.

CAUTION: Use only the ON/OFF switch to reboot your machine. Damage may
occur to your machine if power is removed by other means.

Summary of Contents for WORKCENTRE 5030



























































































































































































Search results

Summary of Contents for WORKCENTRE 5030

Reviews:

Xerox WORKCENTRE 5030, Quick Reference Manual, Page: 182 / 186

Search results

Summary of Contents for WORKCENTRE 5030

Reviews: