Xerox Phaser 790DP Getting Started Manual Download Page 81

Page: 81 / 83

Macintosh OS print drivers

3. Network Setup

Xerox Phaser 790 Getting Started

3-11

Macintosh OS

Before you begin

Ensure the printer has been prepared for network printing.

Ensure you have the printer name, Apple Talk Zone (if applicable), and
IP Address. These may be obtained from your system administrator or
from the Configuration Page.
In order to print the Configuration Page, perform the following steps:

Press the

Offline

button on the Printer Control Panel

Press the

Menu

button until the message

Print Pages from List

displayed on the Printer Control Panel.

Pressthe

Item/Enter

button in order to select

Print Configuration

Page

Pressthe

Item/Enter

again button in order to print the page.

Installing the print drivers

Perform one of the following steps:

•

Insert the User Software CD in your CD-ROM drive and open the

English: Printer Driver

folder.

•

In order to install from files you downloaded using the Installer

WebTool, open the

Printer Driver

folder on your hard disk.

Double-click the

AdobePS 8.6 Installer

icon.

When the Warning dialog box is displayed, select

Yes

Select

Restart

when the installation is complete.

Summary of Contents for Phaser 790DP




















































































Search results

Summary of Contents for Phaser 790DP

Reviews:

Related manuals for Phaser 790DP

Brands by name

Popular brands

Xerox Phaser 790DP, Getting Started Manual

Search results

Summary of Contents for Phaser 790DP

Reviews:

Related manuals for Phaser 790DP

Brands by name

Popular brands