Xerox Phaser 790DP Getting Started Manual Download Page 19

Page: 19 / 83

Installing the 2 Tray Module

1. Setting up the Phaser 790

Xerox Phaser 790 Getting Started

1-9

Installing the 2 Tray Module (optional)

If you ordered the 2 Tray Module, perform the following steps. If you did not
order the 2 Tray Module, go to the

Unpacking the Printer

procedure.

WARNING

You will need at least two people to remove it from the carton.

Open the 2 Tray Module carton.

Remove the styrofoam and the plastic wrap from the top of the 2 Tray
Module.

With a person on each side of the box, grasp the crossbars in the
locations indicated by the labels.

301098a

Lift the 2 Tray Module from the box and place it the selected location.

Lock the front casters as shown below.

301007B-WOL

Summary of Contents for Phaser 790DP




















































































Search results

Summary of Contents for Phaser 790DP

Reviews:

Related manuals for Phaser 790DP

Brands by name

Popular brands

Xerox Phaser 790DP, Getting Started Manual

Search results

Summary of Contents for Phaser 790DP

Reviews:

Related manuals for Phaser 790DP

Brands by name

Popular brands