Xerox FaxCentre F12 Service Manual Download Page 183

Page: 183 / 380

Maintenance & Troubleshooting

WorkCentre Pro 412, FaxCentre F12 &

3/03

7-13

WorkCentre M15/M15i

7-3-2 PC-Scan

Abnormal noise

• Check the scanner glass and any

mechanical disturbance.

• Check the scanner glass is cor-

rectly located and clean, check that
the CCD carriage moves smoothly.

• Check the motor driver in Driver
PBA.

• If any driver is defective, replace

the main PBA.

- U55 or U55-1, 15 = 0V to 24V

swing signal when operating.

PROBLEM

ITEMS TO BE CHECKED.

HOW TO SOLVE

Scanning error

• Check the printer cable.

• Check correct installation, and use

standard IEEE1284 cable.

• Check how TWAIN driver is
installed.

• Remove any other scanner driver.
• Reboot after reinstallation of the

TWAIN driver.

• Check harness contact.

• Check CN14 contact in Main PBA

• Check the IEEE1284 signal level.

• If any signal level is defective,

install a new Main PBA.

- U36-66~74 in Main PBA = 0.8V to

2.4V TTL signal.

• If necessary, install a new PBA

MAIN-MAIN, PL 8-1 item 19

Defective image
quality

• Check shading profile.

• Remake shading profile in the Tech

mode.

• Check the gap between original

and scanner glass.

• A gap greater than 0.5mm can

cause a blurred image.

Abnormal noise

• Check the scanner glass and any

mechanical disturbance.

• Check the scanner glass is cor-

rectly located and clean, check that
the CCD carriage moves smoothly.

• Check the motor driver in Driver

PBA.

• If any driver is defective, replace

the Main PBA.

- U55 or U56-19 = 0V to 24V swing

signal when operating.

PROBLEM

ITEMS TO BE CHECKED.

HOW TO SOLVE

Summary of Contents for FaxCentre F12





























































































































































































































































































































































































Search results

Summary of Contents for FaxCentre F12

Reviews:

Related manuals for FaxCentre F12

Brands by name

Popular brands

Xerox FaxCentre F12, Service Manual

Search results

Summary of Contents for FaxCentre F12

Reviews:

Related manuals for FaxCentre F12

Brands by name

Popular brands