Xerox FaxCentre F12 Service Manual Download Page 130 | Manualshive

Page: 130 / 380

background image

Disassembly and Reassembly

6-18

3/03

WorkCentre Pro 412, FaxCentre F12 &

WorkCentre M15/M15i

6-1-12 Main Frame Assembly

1.

Before you remove the LSU, you should
remove:
- Rear Cover (see page 6-2)
- Scanner Assembly (see page 6-3)
- Side Cover Assembly (see page 6-10)
- Fuser (see page 6-12)
- Exit Assembly (see page 6-13)
- Cover Paper Exit Assembly (see page 6-14)
- SMPS (see page 6-16)
- LSU (see page 6-17)

2.

Remove one screw in the Channel Base
Frame from the bellow section of the Base
Frame, and then remove the rest of the five
screws to dissemble the Dummy Base
Frame, the Cover Front and the Cam Jam
Remove.

3.

Remove the Locker Deve, and then remove
the one screw and the Cover Motor Bracket.

4.

Unplug the all connectors.

5.

Remove the seven screws and take out the
Main Frame Assembly.

Dummy Base Frame

Cam Jam Remove

Front Cover

Lock Deve

Cover Motor Bracket

Main Frame Ass’y

«
...
128
129
130
131
132
...
»

Summary of Contents for FaxCentre F12





























































































































































































































































































































































































Reviews:

No comments

Related manuals for FaxCentre F12

IR5000 - iR B/W Laser

Brand: Canon Pages: 86

DocuPrint C525 A

Brand: Xerox Pages: 49

DocuPrint C2100

Brand: Xerox Pages: 206

Brand: Xerox Pages: 116

Brand: Xerox Pages: 358

Brand: Xerox Pages: 344

Brand: Xerox Pages: 59

Brand: Xerox Pages: 2

Brand: Xerox Pages: 10

Brand: Xerox Pages: 51

Brand: Xerox Pages: 110

7300DX - Phaser Color Laser Printer

Brand: Xerox Pages: 8

8400B - Phaser Color Solid Ink Printer

Brand: Xerox Pages: 203

3150 - Phaser B/W Laser Printer

Brand: Xerox Pages: 2

3117 - Phaser B/W Laser Printer

Brand: Xerox Pages: 8

C8 - DocuPrint Color Inkjet Printer

Brand: Xerox Pages: 148

1235DT - Phaser Color Solid Ink Printer

Brand: Xerox Pages: 239

Brand: Xerox Pages: 64

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands