Xerox 4235 Page 76 Installation Planning Manual Download | Manualshive

Page: 76 / 148

background image

SYSTEM CONFIGURATION

6–10

XEROX 4235 LPS INSTALLATION PLANNING GUIDE

Table 6–3.

Parallel system configuration options

Settings

Options

(defaults appear bold)

Description

Port configuration

1st interface

2nd interface

A three–stop process is used to configure the first port for
parallel:

1.

Select the communication protocol.

2.

Select the current emulation.

3.

Enable or disable the Line Printer Mode.

Note: At least one port must be configured for parallel.

Communication
protocol

Parallel

SNA/SDLC

Asynchronous

Bisynchronous

This option allows you to select the communication protocol
used on the selected interface. In parallel communications,
data is transmitted and received in parallel bytes rather than
serial bits. It is used for local printing over short distances
(10 feet or 3 meters).

Current emulation

XDPM

XPPM

XScript

HP LaserJet IID

This option allows you to select the Current Emulation mode
used on the selected interface. You can select the XDPM,
XPPM, XScript, or HP LaserJet IID emulation modes. Jobs are
processed using the current emulation. With Mode
Switching enabled, an MCK command can dynamically
change the current emulation setting.

Line printer mode

Enable

Disable

This option allows you to enable or disable the Line Printer
Mode option on the selected interface.

Mode switching/
default mode

Enable

Disable

This option allows you to select the Default Emulation mode
used on the selected interface. If enabled, a prompt allows
you to select the Default Emulation mode.

Default emulation

XDPM

XPPM

XScript

HP LaserJet IID

This option allows you to select the Default Emulation mode
in which jobs should print when you encounter an MCK
reset command.

Character code set 7–bit ASCII

EBCDIC

ISO 6937

8–bit ASCII

This option allows you to select the code set and number of
bits per character. EBCDIC and ISO encoding assume eight
bits. XPPM assumes 8–bit encoding. In XPPM, ISO 6937
defaults to 8–bit ASCII. In HP IID mode, EBCDIC, and 7–bit
ASCII are not supported.

«
...
74
75
76
77
78
...
»

Summary of Contents for 4235





















































































































































Reviews:

No comments

Related manuals for 4235

Brand: Qls Pages: 53

Brand: Xerox Pages: 36

Brand: 3DMakerWorld Pages: 85

Replicator Mini+

Brand: MakerBot Pages: 2

Replicator Mini Compact

Brand: MakerBot Pages: 38

Brand: MakerBot Pages: 14

Brand: SainSmart Pages: 13

Brand: Xerox Pages: 12

Brand: MakerBot Pages: 48

Brand: Intamsys Pages: 5

Brand: iFactory3D Pages: 14

Brand: 3DBNZ Pages: 32

Brand: Gainscha Pages: 12

Brand: Telpar Pages: 25

Brand: Citizen Pages: 37

Brand: Konica Minolta Pages: 4

ThermalTronix TT-1025EX-MIL

Brand: Intellisystem Pages: 11

Brand: Citizen Pages: 88

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands