EWV
- 41 -
INSTALLATION
ELECTROFOG
5.4
PLACEMENT OF THE MACHINE
Operator
qualification
Number of
operators
2
Security
measures
- -
Machine
status
The machine must be positioned outside the cold room
to be treated.
To position it, proceed as follows:
- Place the machine on an adequately sized support
to align the fogging pipe (
1
) with the inlet hole of the
cold room and keep it in a stable position.
- Insert the tube (
1
) inside the cold room, for about 40
cm. There is an indicator on the tube that allows you
to see how far the tube can be inserted into the cold
room.
- Make sure that the tube is tilted slightly forward and
adjust its position, if necessary.
- Use insulating material to seal the gap between the
fogging pipe barrel and the cold room.
DANGER
Insulating material must be carefully positioned to
thermally insulate the fogging pipe and seal the
gap between the fogging pipe barrel and the hole
of the cold room where the machine is installed.
Appropriate PPE must be used when handling
insulating material.
- Place a collection container (
3
), containing a small
amount of water, inside the cold room under the tube
outlet (
4
).
DANGER
The machine uses aerosol products (list on page
21) that are potentially hazardous to the operator's
health, as described in the data sheets.
To prevent leakage or spillage of potentially
hazardous aerosol products, use a layer of
fibreglass material (6) to seal the gap between the
fogging pipe barrel and the hole of the cold room
where the machine is installed. This prevents the
aerosol product from escaping.
During the operation, safety equipment (protective
gloves, respiratory protection mask, protective
goggles) must be worn to avoid direct contact
with the aerosol product and avoid inhalation of
fibres or skin irritation.
Summary of Contents for CEDAX ELECTROFOG EWV8
