![background image](http://html1.mh-extra.com/html/xantrex/prosine-ps2-5-and/prosine-ps2-5-and_installation-and-operation-manual_3290836090.webp)
Prosine 2.5/3.0 Installation & Operation Guide
73
Section 7: Batteries
Monthly Battery Maintenance
WARNING
Wear appropriate attire and eye protection. Use caution when working with metal tools
around batteries. Do not allow any metal object to come into contact with both battery terminals at the
same time. Battery explosion or failure can occur.
At a minimum, check the level of the electrolyte in each battery cell once a month (for non-sealed
batteries). It should be above the top of the plates, but not completely full. Most batteries have a
plastic cup that, when full, just touches the electrolyte. Don’t overfill the batteries or the electrolyte
will spill out of the batteries when they are being charged. Refill the batteries with distilled water
only— “spring” water and regular tap water may have high levels of minerals that can poison the
battery chemistry and reduce battery life.
It is also good to periodically check the battery connections for tightness and corrosion. If any
corrosion is found, disconnect power from the Prosine, disconnect the cables, and carefully clean with
a mild solution of baking soda and water.
Do not allow the solution to enter the battery
. Rinse the top
of the battery with clean water when finished.
To reduce the amount of corrosion on the battery terminals, after reassembly, coat them with anti-
corrosion grease or liquid neoprene (liquid electrical tape) available from automotive parts stores or
battery suppliers. Do not apply anything between the terminal and the cable lugs. The connection
should be metal to metal. Apply the protective material only after the bolts have been tightened.
Cleaning Batteries
Dirty batteries may leak current, and tend to run warmer. Cleaning the batteries, when necessary, is
easy and safe when the instructions presented here are followed.
Preparation
You will need appropriate attire, a few tools, and some equipment and supplies on hand. Read over the
list and gather what you need before you begin.
WARNING
Wear appropriate attire and eye protection.
Attire
Appropriate attire might include old clothes, rubber boots or old shoes. Battery acid is very corrosive
and will dissolve most textiles within a few days after exposure, so wear something you can live
without just in case you splash some on yourself. Be sure to wear rubber gloves and eye protection.
Tools
❐
❐
❐
❐
½-inch and/or 9/16 wrench as required, or an equivalent socket and ratchet
❐
❐
❐
❐
adjustable and/or locking pliers
❐
❐
❐
❐
torque wrench (suggested, not required)
❐
❐
❐
❐
soft-bristled brush (discarded toothbrushes work just fine)
❐
❐
❐
❐
6-inch scrub brush
❐
❐
❐
❐
inexpensive ½ inch chip brush or soldering brush
Summary of Contents for Prosine PS2.5 and
