X-lite X-803RS, Safety And Instructions For Use

Page: 20 / 136

20
X803 RS
2 CHECKING AND ADJUSTING THE PINLOCK® INNER VISOR STRETCH
Check the correct PINLOCK
®
inner visor assembly by opening and closing the visor
and making sure that they do not move.
If the PINLOCK
®
inner visor is not tightly fixed to the visor, simultaneously move both
external adjustment levers upwards to increase the stretch (Fig.8). This operation must
be carried out gradually. The maximum stretch is achieved when the pin adjustment
external levers are turned outwards.
WARNING
- The presence of dust between the two visors may produce scratches on both
surfaces.
- Scratched PINLOCK
®
visors and inner visors may cause reduced visibility and
must therefore be replaced.
- Regularly check the correct stretch of the PINLOCK
®
inner visor to prevent it from
moving and scratching both surfaces.
- If the helmet visor fogs up and/or condensation forms between the visors, check
that the PINLOCK ® inner visor is both correctly assembled and stretched.
- An excessive and early stretch of the PINLOCK
®
inner visor may result in exces-
sive adherence against the visor surface and/or permanent deformations with
subsequent inability to correctly perform any following adjustments.
- Intense sweating/breathing, the use under particular weather conditions (low tem-
peratures, high humidity, sudden changes in temperature or heavy rain) or intense
and prolonged use may affect the performance of the PINLOCK
®
inner visor and
cause fogging or formation of condensation. In such cases, to restore the sys-
tem efficiency after using the helmet, remove the PINLOCK ® inner visor from the
helmet visor and let it dry with dry and warm air. The same procedure must be
applied to the helmet, in order to dry out humidity in case it has formed up as a
consequence of the conditions described above.
3 PINLOCK
®
INNER VISOR DISASSEMBLY
3.1 Remove the visor equipped with the PINLOCK
®
inner visor (see instructions above).
3.2 Widen the visor and release the PINLOCK
®
inner visor from the pins (Fig.10).
3.3 Release the visor.
4 MAINTENANCE AND CLEANING
- Remove the PINLOCK
®
inner visor from the visor. Using a damp and soft cloth,
gently clean it with neutral liquid soap. Remove the soap under running water.
- Dry the visor with dry and warm air without wiping it.
- To keep the features of the visor in good conditions over time, let the helmet dry
in a ventilated and dry place with the visor open after use. Keep it away from heat
sources and store it in a place away from direct light.
- Do not use solvents or chemical products.
REMOVABLE INNER COMFORT PADDING
The removable comfort padding consists of:
- a liner
- pads of the side cheek pads (right and left)
INSTRUCTIONS FOR USE
- strap covering
All components can be completely removed and washed. The cheek pads are also
characterised by removable inner expanding foam padding.
1 CHEEK PAD DISASSEMBLY
1.1 Unfasten the chin strap (see relevant instructions).
1.2 Gently pull the red strap in the front area of the pad of the left cheek pad to release
the safety lever on its back (Fig.11).
1.3 Hold the front part of the pad of the left cheek pad and turn it upwards to unhook
the front and upper hooks on its back (Fig.12).
1.4 Pull the back of the pad of the left cheek pad towards the inside of the helmet to
undo the snap fastener on its back (Fig.13).
1.5 Pull the front part of the left cheek pad base upwards until the front fastening “A”
of the frame releases from its corresponding plate between the outer shell and the
polystyrene cheek pad (Fig.14).
1.6 Completely remove the helmet left cheek pad, by flapping the pad base frame out
of the cavity between the outer shell and the polystyrene cheek pad.
Do not remove the polystyrene cheek pads from the helmet shell.
2 DISASSEMBLY OF THE INNER EXPANDING FOAM PADDING OF THE CHEEK PADS
To make it easier to wash the inner comfort padding components, the cheek pads of
the helmet are fitted with inner expanding foam padding that can be removed from the
fabric lining. To remove the padding, proceed as follows after removing the cheek pads
from the helmet (see instructions above).
2.1 Gently remove the inner expanding foam padding from the fabric lining of the left
cheek pad (Fig.15).
2.2 Repeat these steps with the right cheek pad padding.
WARNING
- Once the inner paddings of the cheek pads in expanding foam have been re-
moved, make sure that the back snap button “D”, the fastenings “A” and the
NERS safety lever “B” are correctly fastened to the rear frame of the fabric lining
of the cheek pads(Fig.16). Otherwise, correctly put them back.
3 DISASSEMBLY OF THE CHIN STRAP COVERING
To remove the chin strap covering from the strap, proceed as follows after removing the
cheek pads from the helmet (see instructions above).
3.1 Pull the left covering strap in line with the “hook and loop fastener” to separate it
from the chin strap band and then take it off (Fig.17A).
3.2 Repeat these steps with the right covering strap.
4 LINER DISASSEMBLY
4.1 Release the left rear flap of the liner from the shell rear edge by slightly puling the
comfort padding towards the inside of the helmet (Fig.18). Follow the same steps
for the right rear flap.