background image

Tel:  +49 (0) 8641 6948 - 60  |  xgloo.com  |  [email protected]

7

  -  On tarmac or similarly-hard 

ground surfaces the tents must 
be sufficiently ballasted (see  
X GLOO wind certificate).

2)   Additionally, you must use an-

choring lines/webbing attached 
to the shoulder loops (found on 
the outside of each Tube) to se-
cure the Event Tent!

•   In windy conditions, be sure to set 

up the tent at such an orientation to 
the wind so that it offers the least 
resistance. In particular, Canopies 
and openings which are closed with 
Walls should not be aligned against 
stronger winds. Wind loads can be 
significantly reduced by detatching 
the Walls and Canopies.

CAUTION: 

In the case of 

wind, the zippers on any Walls 
or other optional Components 
connected to the Tent must 
always be pulled completely 
closed, otherwise the zipper 
can be damaged by exces-
sively-high wind loads put on 
individual teeth of the zipper.

Wind gusts exceeding the maximum 
speed that the Event Tent is certi-
fied for can lead to structural da-
mage to the Tent that is not cove-
red by the warranty.

CAUTION: 

If weather con-

ditions deteriorate dramatically, 
all overpressure valves must be 
opened immediately and the 
tent deflated. 

Additionally, the deflated Tent 
should be weighted down in order 
to prevent the wind from taking hold 
of it.

 

OPERATION

•   The inflatable X GLOO Event Tent 

is not intended for continuous use 
and should be inspected for wear 
or damage after every event. 

CAUTION:

 The protective 

strips on the bottom of the 
Tubes can wear down when 
the Event Tent is set up on 
rough terrain and wind causes 
the Tent to shift around, and 
should therefore be regularly 
checked for wear and replaced 
as necessary before the Tubes 
themselves become damaged.

•   X GLOO Tents are not intended to 

bear large snow loads.

CAUTION:

 In case of 

snowfall the accumulating 
snow must be regularly remo-
ved from the Roof of the Tent. 
If the Tent is unattended and 
snowfall is called for, then the 
Tent is to be deflated.

•   All X GLOO Tents are made of cer-

tified flame-retardant materials. 
Nevertheless, these are flammable 
substances which burn when the 
source of fire is sufficiently strong.

CAUTION:  

Keep the Event 

Tent away from open fires and 
heat sources.

•  Fire protection classification  

(see available X GLOO certificates):

  -  DIN 4102-B1 (Abb.: B1) Controls 

testing and requirements on the 
reaction to fire of building mate-
rials. German norm, used in most 
European countries.

Continued on the next page...

Summary of Contents for XC Series
































Reviews: