background image

Tel:  +49 (0) 8641 6948 - 60  |  xgloo.com  |  [email protected]

15

a

b

c

ANCHORING WITH WATER BALLAST 
BARRELS

The Water Ballast Barrels can be used as anchors for your 
inflatable X GLOO Event Tent, as seating, or as both.

To fill

1   Open the two valve covers on the Ballast Barrel. 

Make sure that the check valve at the bottom of the 
Barrel is closed so that no water or air can escape 
when filling (a). Push open the check valve at the 
top of the barrel so that air can escape.

2   Connect the included hose to the valve at the base 

of the barrel and fill with the desired amount of wa-
ter (up to 80L). To give the Barrel a cleaner appea-
rance, the remaining space can be then filled with 
air using one of our Electric Pumps. Connect the 
hose provided with the Ballast Barrels to the Pump 
in place of the Pump‘s yellow hose.

3   Disconnect the hose from the Barrel and make sure 

that both valves are tightly closed.

4   With the help of an assistant, carry the Ballast Bar-

rel to your tent location by lifting it by the handles. 
Or, if you are on your own, tip the barrel onto its 
edge and roll it.

Connecting to your inflatable X GLOO Event Tent

Ballast Barrels are connected to the Event Tent by use 
of an included shackel. Whether connecting one or two 
Ballast Barrels to each Tube, use the shackle to attach 
the eyelet at the base of each Ballast Barrel directly to 
the anchoring ring at the base of the Tube (b). 

Digitally-Printed Cover (c)

The Ballast Barrels can be uniquely branded through the 
use of the Digitally-Printed Cover. Simply slip the cover 
over the Barrel and close the zipper.

To empty

To empty the Ballast Barrel, simply unscrew the  
lower valve cover and push open the check valve.

Find all of our how-to videos at:  
xgloo.com/howto

Summary of Contents for XC Series
































Reviews: