manualshive.com logo in svg

Woodward 2301E-ST, Installation And Operation Manual

Share
Download
Woodward 2301E-ST Installation And Operation Manual Download Page 122

Manual 26694 

2301E-ST 

 

 

 

Woodward 

120 

First Out Trip Indication 

The integer loaded into the 2301E-ST’s “Trip First Out” indication register 3:0001 indicates the first event 
sensed which caused the controller to shutdown. Refer to Table B-1 for integer-to-event relationship. 
 

Table B-2. Trip First Out Indication 

 

1. Power up Shutdown 
2. Overspeed Shutdown 
3. Both Speed Probes Failed 
4. Analog Input #1 Failed 
5. Analog Input #2 Failed 
6. Modbus Issued Shutdown 

 

First Out Alarm Indication 

The integer loaded into the 2301E-ST’s “Alarm First Out” indication register 3:0002 indicates the first 
Alarm event sensed since a “Reset” command was given. Refer to Table B-2 for integer to event 
relationship. 
 

Table B-3. Alarm First Out Indication 

 

1.  Analog Input #1 Failed 
2.  Analog Input #2 Failed 
3.  Internal Load Sensor Failed 
4.  Loadshare Analog Line Failed 
5.  Speed Senor #1 Failed 
6.  Speed Sensor #2 Failed 
7.  > Max Difference Between Speed Sensors 

 

 

Released

Summary of Contents for 2301E-ST































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands