manualshive.com logo in svg

Woodstock ShopFox W1763W, Owner'S Manual, Page: 9 / 64

Share
Download
Woodstock ShopFox W1763W Owner'S Manual Download Page 9

-7-

Model W1763W (For Machines Mfd. Since 09/16)

IN

TR

O

DU
CT

IO

N

Controls.&.Components

Refer to the 

Figures.2–4

 and the following descriptions to 

become familiar with the basic controls and components 

of this machine. Understanding these items and how they 

work will help you understand the rest of the manual and 

stay safe when operating this machine.

STOP/Reset Button: Press to turn machine 

OFF

. Twist 

button clockwise to reset.

START Button: Press to turn machine 

ON. 

START button 

illuminates when machine has power.

Spindle Direction Switch: Adjusts cutter rotation left or 

right. "0" is the neutral (off) position.

Spindle Height Lock Knob: Locks spindle and cutter 

height adjustments.

Fence Offset Knob: Adjusts fence offset independently by 

rotating clockwise or counterclockwise.

Fence Lock Knob: Locks fence in place.

Fence: Independently adjustable side-to-side and front-to-

back. Also removable for easy replacement with a zero-

clearance or other custom-made fence.

Carriage Lock Knob: Tighten to secure entire fence/

carriage assembly on table. Loosen to allow entire fence/

carriage assembly to pivot around cutterhead opening, or 

remove it altogether for freehand shaping.

Workpiece Hold-Down: Assists with holding workpiece 

tight against work table as it is fed through cutter.

Cutter Guard: Protects user from chips thrown by 

cutterhead and allows for a clear view of workpiece 

cutting area

Support Arm & Adjustment Knobs: Adjustment knobs 

move cutter guard and hold-down along support arm.

Figure.2

. Control arm components.

START 

Button

Figure.4.

 Shaper components (front view).

Fence

(1 of 2)

Carriage 

Lock Knob

(1 of 2)

Hold-Down

Knob

Support Arm 

Knob

STOP/Reset

Button

Spindle 

Direction 

Switch

Figure.5.

 Shaper guard components.

Support 

Arm

Workpiece 

Hold-Down

Cutter 

Guard

Cutter 

Guard Knob

Figure.3.

 Carriage assembly (rear view).

Fence Offset 

Knob (1 of 2)

Fence 

Lock Knob 

(1 of 2)

Spindle Height 

Lock Knob

To.reduce.the.risk.of.serious.injury.

or. damage. to. the. machine,. read.

this. . entire. manual. BEFORE. using.

machine.

Summary of Contents for ShopFox W1763W

































































Reviews:

No comments