Woodstock ShopFox W1763W Owner'S Manual Download Page 43

-41-

Model W1763W (For Machines Mfd. Since 09/16)

O

PE

R

ATIO
NS

ACCESSORIES

Shaper.Accessories

The following shaper accessories may be available through your local Woodstock International Inc. 

Dealer. If you do not have a dealer in your area, these products are also available through online 

dealers. Please call or e-mail Woodstock International Inc. Customer Service to get a current listing of 

dealers at: 1-800-840-8420 or at [email protected].

W1110—

1

2

".Rub.Collar,.1-

1

8

".Outside.Dia.

W1112—

1

2

".Rub.Collar,.1-

3

8

".Outside.Dia.

W1113—

1

2

".Rub.Collar,.1-

1

2

".Outside.Dia.

If you do any kind of irregular shaping, rub collars are a must! Rub 

collars are used for shaping curved work such as cathedral doors, as 

well as many custom shapes. They are also used for limiting depth-

of-cut, like guide bearings on router bits.

W1164—Spacer.

3

4

".Bore,.1-

1

4

".OD,.

1

4

".High

W1165—Spacer.

3

4

".Bore,.1-

1

4

".OD,.

3

8

".High

W1166—Spacer.

3

4

".Bore,.1-

1

4

".OD,.

1

2

".High

W1167—Spacer.

3

4

".Bore,.1-

1

4

".OD,.

3

4

".High

W1168—Spacer.

3

4

".Bore,.1-

1

4

".OD,.1".High

Spacers allow you to position your shaper cutter anywhere on the 

spindle. Use them between cutters or stack them above the cutter 

to bear against the spindle nut. Every shaper owner needs a set of 

these on-hand.

W1114—

3

4

".Rub.Collar,.1-

5

8

".Outside.Dia.

W1116—

3

4

".Rub.Collar,.1-

3

4

".Outside.Dia.

W1118—

3

4

".Rub.Collar,.1-

7

8

".Outside.Dia.

W1119—

3

4

".Rub.Collar,.2".Outside.Dia.

W1120—

3

4

".Rub.Collar,.2-

1

8

".Outside.Dia.

W1122—

3

4

".Rub.Collar,.2-

5

8

".Outside.Dia.

If you do any kind of irregular shaping, rub collars are a must! Rub 

collars are used for shaping curved work such as cathedral doors, as 

well as many custom shapes. They are also used for limiting depth-

of-cut, like guide bearings on router bits.

D3726—30.Pc..Carbide-Tipped.Router.Bit.Set,.

1

4

".Shank

These are super sharp, micro-grain carbide tipped bits that are 

ground up to 800-grit to glide through your cuts. Includes protective 

wooden case with see-thru, touch latch doors for easy access.

Summary of Contents for ShopFox W1763W

































































Reviews: