WM Systems M2M Router NB User Manual Download Page 56 | Manualshive

Page: 56 / 60

background image

Checking the connection - connecting to the router through USB
Download and install driver for USB connection from our website:

https://www.m2mserver.com/m2m-downloads/USB_Ethernet_RNDIS_DRIVER.zip

Unpack the downloaded zipped file and install the driver. After you’ve connected the USB cable you
can add the driver at the Windows / Start / Control Panel / System / Device Manager. Find
the Network Cards, extend it and you will found the „USB Ethernet / RNDIS Gadget”. Double
click on the entry and choose the Driver tab, and the Refresh button, then browse the
uncompressed file’s directory then Install the driver.)
Build a connection between the PC and the router with a micro-USB cable. (The driver must be

installed on the PC – related the

Installation Manual).

Configure the USB-Ethernet interface IP address on your PC for the „USB Ethernet/RNDIS
Gadget” and setup the next fixed ipv4 address: 192.168.10.10, subnet mask is: 255.255.255.0 –
connect these settings.
(You can ping the device through the USB connection on its IP address.)

If the router is not starting

After adding the power source to the router and none of its LEDs are not lighting after 2 minutes,

then it is possible that there the firmware or software damaged. Ask our support line!

Periodic restart of the router (by 10 minutes periods)
When router was not be configured properly for the ppp/wan connection or the modem was not
started then the router will be restarted within in 10 minutes.
You can also configure the periodic ping interval from the LuCi / OpenWrt.

Restart of the router

If the router is not responding permanently, you can restart it by disconnecting power cable
(POWER titled microfit connector) then after a few second plug it again. The LEDs must assign the
presence of the power source.

Shutdown / halt the router
To shutdown the router, first you have to reboot by the System / Reboot menu. When all the
three LEDs blinks at once, the router is restarted and can be switched off safely as soon as you can

– pull out the power connector from electricity plug.

«
...
54
55
56
57
58
...
»

Summary of Contents for M2M Router NB





























































Reviews:

No comments

Related manuals for M2M Router NB

Brand: IBM Pages: 32

Brand: Paradyne Pages: 2

Brand: Falcon Pages: 24

Brand: I-O Wireless Pages: 55

SLK-R602 Series

Brand: Seriallink Pages: 29

LBON320AC Series

Brand: Lindsay Broadband Pages: 4

Brand: Valcom Pages: 4

Brand: TRENDnet Pages: 10

Brand: Lantech Pages: 40

Brand: Hunter Pages: 2

Brand: Tripp Lite Pages: 34

Brand: Softing Pages: 16

Brand: IBM Pages: 168

Brand: Clas Ohlson Pages: 4

Brand: Rajant Pages: 93

Brand: Abocom Pages: 59

Brand: Me Pages: 28

Brand: Allied Telesis Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands