background image

 

 

12

WT-009 GSM Remote Control Device 

WT-009– USER MANUAL – Rev.2.3 – Technical Support: 

[email protected] 

  

COPYRIGHT ©2008 WITURA CORPORATION SDN BHD 

 
 

 

To read the sub increment counter value, you can send the following SMS message to 
the unit. 
 

Text Command: 
 
#COT? 

 

 

The syntax of the command is the following:

 

 
 #PWD123456#COT? 

 
 

You will receive the sub increment value from the unit by SMS. 

 

Note:  The sub increment counter value will be reset automatically each time the alarm 

counter reached the alert value. 

 
 

 

 

To reset the total counter value, you can send the following SMS message to the unit. 
 

Text Command: 
 
#CLA 

 

 

The syntax of the command is the following:

 

 
 #PWD123456#CLA 

 

 
 

 
 

 
 

To activate the output relay, you can send a text command via SMS specifying the 
number of seconds the output should  stay  on  to  the  unit. 

It 

is

 

possible to set up to 

maximum of 65,535 seconds 

 

5.2 OUTPUT 

SETTINGS

 

5.1.8  READING THE TOTAL COUNTER VALUE

 

5.1.9  RESET THE TOTAL COUTER VALUE

 

5.2.1  ACTIVATE THE OUTPUT RELAY TO STAY ON FOR A SPECIFIC TIME

 

Summary of Contents for WT-009



















Reviews: