Wintriss Shadow VI User Manual Download Page 93

Page: 93 / 159

Shadow VI User Manual

1107200

Troubleshooting Shadow VI

Chapter 4

page 81

Inside the Control

There are eight LED indicators on the circuit board inside the control (refer to Figure 2-14 in
Chapter 2 for location of components).

DS1

and

DS2

are located just above the TB2 receiver connectors at the lower right-hand

corner of the board, and do not light up under normal conditions. However, they light up

red

if you are using only 1 set of curtains and there is an obstruction. If you have 2 sets, DS1
lights up red when Set 1 (wired to the upper connectors of TB2 and TB3) is interrupted. DS2
corresponds with Set 2, which are wired to the lower connectors.

DS3

and

DS4

, located in the upper right-hand corner of the control near the power supply,

normally light up

green

all the time, indicating that the optic heads are receiving power.

DS5

and

DS6

are located in the lower left corner of the board below TB4. They light up

orange

when you are using external MPCE monitoring and there is an obstruction in the

light field. See “External MPCE Monitoring: Checking DS5 and DS6” on page 85.

DS7

is located in the lower left corner of the board below TB4. It is off under normal

conditions, but lights up

yellow

when “Reset” is on.

DS8

is located in the lower left corner of the board. Under normal conditions, it lights up

green

, indicating that the transmitter is active.

Summary of Contents for Shadow VI
































































































































































Search results

Summary of Contents for Shadow VI

Reviews:

Related manuals for Shadow VI

Brands by name

Popular brands

Wintriss Shadow VI, User Manual

Search results

Summary of Contents for Shadow VI

Reviews:

Related manuals for Shadow VI

Brands by name

Popular brands