Wintriss Shadow VI User Manual Download Page 18 | Manualshive

Page: 18 / 159

background image

1107200

Shadow VI User Manual

page 6

Chapter 1

Introduction to Shadow VI

Safety Light Curtain

Because the receiver only accepts

infrared

light pulses of a certain duration in proper

sequence, Shadow cannot be affected or fooled by other light sources. All other continuous
light sources and even pulsed light sources are "tuned out." Therefore, the light curtain is not
affected by normal lighting near the light curtain. Also, changes in area lighting or even
flashing strobe lights will not affect operation.

This pulsed sequence is so fast that, where we mark time in units no smaller than a second,
the effect is a continuous light field across the guarded area. You would have to move the
point of your finger across an LED in the transmitter in less than 5/1000th of a second (5 ms
or milliseconds) to evade the light pulses coming from that LED. Therefore in our world of
seconds and minutes, the light curtain is really always there even though only one light beam
is actually produced at a time. The actual light pulse lasts for only 1/100,000th of a second
(10 microseconds). Consequently it does not take long to create a whole series of pulses one
after the other.

Shadow and Control Reliability

WARNING

!

IMPROPER INSTALLATION

•

Install Shadow safety light curtains in compliance with applicable safety regulations from the

Occupational Safety and Health Administration (OSHA) and the American National
Standards Institute (ANSI). See excerpts in the appendices.

•

Refer to the latest revision of all applicable documents.

•

Ensure that your installation meets the control reliability requirements of the applicable

regulations.

•

Ensure that both Shadow control relays are used in any Shadow installation, including

connection directly to the press control's stop circuit, to a PLC, or to other type of machine
control. Wiring is explained in Chapter 2.

•

Read carefully and understand the installation instructions before attempting to install and

wire Shadows to any control

•

Ensure that installation is performed by qualified personnel.

Failure to comply with these instructions could result in death or serious injury.

WARNING

!

UNPROTECTED MACHINERY MAY CONTINUE TO OPERATE

Ensure that all operators know which device(s) your Shadow safety light curtain protects and

which it does not. The press Shadow is wired to will stop when the light curtain is
interrupted and sends a stop signal to the press. However, the associated feeds and
conveyors, to which Shadow is not wired, will continue to operate after the press stops.

Failure to comply with these instructions could result in death or serious injury.

Shadow is control reliable. Control reliability is a term used and defined in the same way by
the Occupational Safety and Health Administration (OSHA) and the American National
Standards Institute (ANSI).

«
...
16
17
18
19
20
...
»

Summary of Contents for Shadow VI
































































































































































Reviews:

No comments

Related manuals for Shadow VI

Brand: OFM Pages: 3

Brand: Office Star Products Pages: 2

Brand: Saint Birch Pages: 12

Brand: ofichairs Pages: 3

Brand: Uberhaus Pages: 13

Brand: Galipette Pages: 12

Brand: LuxenHome Pages: 14

Brand: realspace Pages: 24

OPTION TIROIR 190 400

Brand: Gami Pages: 3

Brand: gbo Pages: 32

Brand: CALIMA Pages: 4

Brand: Forever Redwood Pages: 7

ARDEN JBSITSTBLK

Brand: J.Burrows Pages: 3

Brand: Forte Pages: 14

Page Recessed Medicine Cabinet

Brand: PotteryBarn Pages: 3

TOBAGO 151-101-5MOD-V5

Brand: HAMPTON BAY Pages: 20

Brand: Walker Edison Pages: 19

Brand: OfficeSource Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands