Wintriss Shadow VI User Manual Download Page 24

Page: 24 / 159

1107200

Shadow VI User Manual

page 12

Chapter 1

Introduction to Shadow VI

Safety Light Curtain

Table 1-1. Shadow VI Specifications

WARNING

INDICATOR OUTPUTS NOT SUITABLE FOR SAFETY USE

•

DO NOT use the indicator outputs listed in the specifications table for personnel protection.

They cannot be used to stop the machinery.

•

Use the safety outputs for personnel protection.

Failure to comply with these instructions could result in death or serious injury.

Scanning heights

9 models: 6, 12, 18, 24, 30, 36, 42, 48 and 60 inches
(15.2, 30.5, 45.7, 61.0, 76.2, 91.4, 106.7, 121.9, and 152.4 cm)

Scanning range

Standard: up to 25 ft (7.6 m)
Extended: up to 50 ft (15.3 m)

Transmitter and receiver not matched sets

Beam spacing

/4" (1.9 cm) centers

Object sensitivity

/4" (3.2 cm)

Response time

30 msec max. for 6" to 24"

35 msec max. for 30" to 48"

40 msec max. for 60"

Size
Optic heads
Control enclosure

See Figures 2-4, 2-5, and Table 2-1 in Chapter 2.
7" x 9" x 3.5" (17.8 x 22.9 x 8.9 cm). See Figure 2-13 in
Chapter 2.

Weight
6" optic heads

Control

1.4 lbs (.64 kg) ; add 0.9 lbs (.4 kg) for every additional
6 inches in height

9 lbs. (4 kg)

Construction

Heads

Control

Cables

Extruded aluminum; 0.12" (3 mm) wall min

18-gauge welded steel with enclosure keylock.

5, 15, 25, 50, and 100 ft. with connector at the optic head.

Environmental

Heads

Control

Cables

Vibration

NEMA 4, IP65; Optional explosion-proof enclosures.

NEMA 2 / IP52; Optional NEMA 4/IP65; Optional with 4
connectors for 2 sets of optic heads; Optional explosion-
proof enclosure.

NEMA 4 connector; Oil-resistant PVC cable standard;
Optional SJOOW cable with 1 or 2 connectors.

10g, 0.03" displacement; freq. 10-150 Hz sine, per UL491
(applies to all three axes).

Summary of Contents for Shadow VI
































































































































































Search results

Summary of Contents for Shadow VI

Reviews:

Related manuals for Shadow VI

Brands by name

Popular brands

Wintriss Shadow VI, User Manual

Search results

Summary of Contents for Shadow VI

Reviews:

Related manuals for Shadow VI

Brands by name

Popular brands