Wintriss Shadow VI User Manual Download Page 38 | Manualshive

Page: 38 / 159

background image

1107200

Shadow VI User Manual

page 26

Chapter 2

Installation and Checkout

Height Considerations

DANGER

!

IMPROPER INSTALLATION

Ensure that the light curtain is installed so it is impossible for anyone to reach over, under, or

around the light curtain and into the hazardous area of the machine without being detected.
Use the correct height light curtain, combined with ancillary physical guards.

Failure to comply with these instructions will result in death or serious injury.

DANGER

!

OPERATOR CAN BE BETWEEN LIGHT CURTAIN AND HAZARDOUS AREA

Ensure that the operator cannot position him- or herself between the light curtain and the

hazardous area. Use another pair of light curtains or a mechanical barrier at knee-to-waist
height to prevent the operator or a passerby from being “trapped” between the light curtain
and the hazard.

Failure to comply with these instructions will result in death or serious injury.

Once you have determined the correct safety distance, you must select the proper curtain
height. Shadow VI comes in sizes ranging from 6" to 60". Shadow must be installed so it is
impossible for anyone to reach over, under, or around the light curtain and into the hazardous
area of the press without being detected. This is accomplished with the proper height light
curtain, combined with ancillary physical guards.

Designing and Mounting Brackets

Once you have calculated the correct safety distance, you can mount your Shadow
transmitter and receiver at this distance from the nearest pinch point (or other hazardous area
of the press). This set of steps lists all the information and dimensions you need to know to
do a good job in designing and mounting brackets. It covers:

1. What requirements you must meet when choosing your mounting location.

2. How to design and mount the brackets so that the Shadow heads can be easily aligned.

3. Maximum openings for side guards used with Shadow light curtains for three-sided

guarding.

4. Mounting Shadow light curtains with mirrors.

5. Mounting Shadow light curtains upside down.

A careful reading of this material will ensure that you will not have trouble mounting and
aligning your Shadow light curtains. After you read this material, design and mount your
brackets.

Universal Mounts

The Shadow VI transmitter and receiver come with universal mounts. These universal
mounts are located at the top and bottom of each head and are held into place by mounting

«
...
36
37
38
39
40
...
»

Summary of Contents for Shadow VI
































































































































































Reviews:

No comments

Related manuals for Shadow VI

Brand: Safco Pages: 4

Brand: Jason.L Pages: 11

Brand: Made Pages: 8

Brand: NABBI Pages: 12

TRADDNG9PCSW8-BLU

Brand: Hanover Pages: 7

Brand: Gami Pages: 7

Brand: Gami Pages: 36

Brand: Gami Pages: 120

Brand: Gautier Pages: 12

SINGLE BUS PANEL 3730

Brand: Twoey Pages: 4

Brand: Avenue Six Pages: 7

Brand: Guidecraft Pages: 4

Brand: Home Decorators Collection Pages: 16

0-65857-17298-0

Brand: Dorel Living Pages: 60

AMERIWOOD INDUSTRIES 5497015PCOM

Brand: Dorel Pages: 16

Brand: MotoSleep Pages: 10

CHARLOTTE S-313SW

Brand: Unfinished Furniture of Wilmington Pages: 5

Brand: Hanover Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands