WinSystems EBC-C413 Product Manual Download Page 9

Page: 9 / 83

EBC-C413/General Operation

v1.2

www.winsystems.com

Page 9

General Operation

The EBC-C413 is a single board computer (SBC). It is a full-featured

embedded system with a variety of onboard I/O options. The following

figure is a simplified system block diagram of the EBC-C413.

Three display interfaces (VGA, DP Mini DisplayPort, and LVDS) support

dual video (up to two simultaneous independent displays) along with

stereo audio. Communication interfaces include two Gigabit Ethernet

ports, eight USB 2.0 ports with ESD suppression, four serial, 48 digital I/O

lines with event sense, a watchdog timer, a PS/2 keyboard and mouse

controller, and a parallel port (LPT).

The EBC-C413 can provide an upgrade for an existing EBX-compatible SBC.

It is designed for harsh environments and reliability, featuring added

shock and vibration resistance, and provides a fanless solution for

operating temperatures between -40°C and +85°C (-40°F and +185°F).

The EBC-C413 processor options provide single, dual, or quad-core

processing. Each soldered-processor option can support up to 8 GB of

DDR3L memory and optional stackable PC104-Plus connectors.

DDR3L

SODIMM

x64

LPC

E3815

E3825

E3845

VGA

DPØ/Mini DP

LVDS

USB 1-4
(5-8 via HUB)

Audio

MiniCard/
mSATA

PC/1Ø4-

Plus

Gigabit Enet (2)

MUX

USB

Audio

SATA

CFast

SATA

PCIe

Display Controller

PC/1Ø4

DIO48

FPGA

SUPER I/O

Four serial ports (RS 232/422/485)

PS/2 keyboard, mouse, LPT

DisplayPort to LVDS

USB Power Switch

HD Audio Codec

PCIe to PCI Bridge

MiniCard

PCIe Packet Switch

MUX

Summary of Contents for EBC-C413




















































































Search results

Summary of Contents for EBC-C413

Reviews:

Related manuals for EBC-C413

Brands by name

Popular brands

WinSystems EBC-C413, Product Manual

Search results

Summary of Contents for EBC-C413

Reviews:

Related manuals for EBC-C413

Brands by name

Popular brands