WinSystems EBC-C413 Product Manual Download Page 73

Page: 73 / 83

EBC-C413/Best Practices

v1.2

www.winsystems.com

Page 73

Mounting and Protecting the EBC-C413

The EBC-C413 must be mounted properly to avoid damage.

The

following standoff kits are available and recommended for use with the

EBC-C413:

• KIT-PCM-STANDOFF-4: Four-piece nylon hex PC104 standoff kit
• KIT-PCM-STANDOFF-B-4: Four-piece brass hex PC104 standoff kit

The following table lists the items contained in each kit.

Placing the EBC-C413 on Mounting Standoffs

—Be careful when placing

the EBC-C413 on the mounting standoffs. Sliding the board around until

the standoffs are visible from the top can cause component damage on

the bottom of the board.

Do Not Bend or Flex the EBC-C413

—Bending or flexing can cause

irreparable damage. Embedded computer modules are especially

sensitive to flexing or bending around Ball Grid Array (BGA) devices. BGA

devices are extremely rigid by design and flexing or bending the

embedded computer module can cause the BGA to tear away from the

printed circuit board.

Mounting Holes

—The mounting holes are plated on the top, bottom and

through the barrel of the hole and are connected to the embedded

computer module’s ground plane. Traces are often routed in the inner

layers right below, above or around the mounting holes.

• Never use a drill or any other tool in an attempt to make the holes

larger.

• Never use screws with oversized heads. The head could come in con-

tact with nearby components causing a short or physical damage.

• Never use self-tapping screws; they compromise the walls of the

mounting hole.

• Never use oversized screws that cut into the walls of the mounting

holes.

Kit

Component

Description

Qty

KIT-PCM-STANDOFF-4
4 pc. nylon hex PC104

standoff kit

Standoff

Nylon 0.25” hex, 0.600” long

male/female 4-40

Hex Nut

Hex nylon 4-40

Screw

Phillips-pan head (PPH)

4-40 x 1/4” stainless steel

KIT-PCM-STANDOFF-B-4
4 pc. brass hex PC104

standoff kit

Standoff

Brass 5 mm hex, 0.600” long

male/female 4-40

Hex Nut

4-40 x 0.095 thick, nickel finish 4

Screw

Phillips-pan head (PPH)

4-40 x 1/4” stainless steel

Summary of Contents for EBC-C413




















































































Search results

Summary of Contents for EBC-C413

Reviews:

Related manuals for EBC-C413

Brands by name

Popular brands

WinSystems EBC-C413, Product Manual

Search results

Summary of Contents for EBC-C413

Reviews:

Related manuals for EBC-C413

Brands by name

Popular brands