WinSystems EBC-C413 Product Manual Download Page 30

Page: 30 / 83

EBC-C413/Configuration

v1.2

www.winsystems.com

Page 30

• CBL-USB4-002-12: Pico-Clasp to 2 each, 2 x 4, 2 mm pitch housing

(shown)

7.12.9 USB2 - USB Connector for Ports 4-7

Connect to the USB signals provided at the USB2 connector.

NOTE The EBC-C413 provides eight USB2.0 ports with ESD suppression (four

ports at USB1 and four at USB2).

Layout and Pin Reference

Additional Information

This connection is a Molex 501571-2007, 2 x 10, 1 mm pitch (Pico-Clasp™

or equivalent) right-angle locking header connector (WS G650-2020-7HB).

Matching connector: Molex 501189-2010 housing with Molex 501193-2000

crimp pins. WINSYSTEMS cables simplify connections to the board:

• CBL-USB4-000-14: Pico-Clasp to unterminated
• CBL-USB4-001-12: Pico-Clasp to Pico-Clasp

PIN 1

Pin

Name

Pin

Name

+V5S_USB3

USBD4-

USBD5-

USBD4+

USBD5+

GND

+V5S_USB4

USBD6-

USBD7-

USBD6+

USBD7+

GND

Summary of Contents for EBC-C413




















































































Search results

Summary of Contents for EBC-C413

Reviews:

Related manuals for EBC-C413

Brands by name

Popular brands

WinSystems EBC-C413, Product Manual

Search results

Summary of Contents for EBC-C413

Reviews:

Related manuals for EBC-C413

Brands by name

Popular brands