WinSystems EBC-C413 Product Manual Download Page 81

Page: 81 / 83

EBC-C413/Power-on Self-Test (POST) Codes

v1.2

www.winsystems.com

Page 81

PostBDS Phase

The PostBDS phase 8-Bit POST code values are shown in the table below.

The S3 phase 8-Bit POST code values are shown in the table below.

BDS_ENUMERATE_ALL_BOOT_OPTION

Get boot device information

BDS_END_OF_BOOT_SELECTION

End of boot selection

BDS_ENTER_SETUP

Enter Setup menu

BDS_ENTER_BOOT_MANAGER

Enter Boot manager

BDS_BOOT_DEVICE_SELECT

Try to boot system to OS

BDS_EFI64_SHADOW_ALL_LEGACY_ROM Shadow Misc Option ROM

BDS_ACPI_S3SAVE

Save S3 resume required data in RAM

BDS_READY_TO_BOOT_EVENT

Last chipset initialization before boot to OS

BDS_GO_LEGACY_BOOT

Start to boot Legacy OS

BDS_GO_UEFI_BOOT

Start to boot UEFI OS

BDS_LEGACY16_PREPARE_TO_BOOT

Prepare to Boot to Legacy OS

BDS_EXIT_BOOT_SERVICES

Send END of POST Message to ME via HECI

BDS_LEGACY_BOOT_EVENT

Last chipset initialization before boot to Legacy OS

BDS_ENTER_LEGACY_16_BOOT

Ready to Boot Legacy OS

BDS_RECOVERY_START_FLASH

Fast recovery start flash

BDS_START_SDHC_BUS

SDHC device initialization

BDS_CONNECT_ATA_LEGACY

ATA legacy device initialization

BDS_CONNEC_SD_LEGACY

SD legacy device initialization

Value

Functionality Name

Description

POST_BDS_NO_BOOT_DEVICE

No Boot Device

POST_BDS_START_IMAGE

UEFI Boot Start Image

POST_BDS_ENTER_INT19

Legacy 16 boot entry

POST_BDS_JUMP_BOOT_SECTOR

Try to Boot with INT 19

Value

Functionality Name

Description

S3_RESTORE_MEMORY_CONTROLLER

Memory initialization for S3 resume

S3_INSTALL_S3_MEMORY

Get S3 resume required data from memory

S3_SWITCH_STACK

Start to use memory during S3 resume

S3_MEMORY_CALLBACK

Set cache for physical memory during S3 resume

S3_ENTER_S3_RESUME_PEIM

Start to restore system configuration

S3_BEFORE_ACPI_BOOT_SCRIPT

Restore system configuration stage 1

S3_BEFORE_RUNTIME_BOOT_SCRIPT

Restore system configuration stage 2

S3_BEFORE_RELOCATE_SMM_BASE

Relocate SMM BASE during S3 resume

S3_BEFORE_MP_INIT

Multi-processor initialization during S3 resume

S3_BEFORE_RESTORE_ACPI_CALLBACK

Start to restore system configuration in SMM

S3_AFTER_RESTORE_ACPI_CALLBACK

Restore system configuration in SMM complete

S3_GO_TO_FACS_WAKING_VECTOR

Back to OS

Value

Functionality Name

Description

Summary of Contents for EBC-C413




















































































Search results

Summary of Contents for EBC-C413

Reviews:

Related manuals for EBC-C413

Brands by name

Popular brands

WinSystems EBC-C413, Product Manual

Search results

Summary of Contents for EBC-C413

Reviews:

Related manuals for EBC-C413

Brands by name

Popular brands