WinSystems EBC-C413 Product Manual Download Page 69

Page: 69 / 83

EBC-C413/Cables and Accessories

v1.2

www.winsystems.com

Page 69

Cables and Accessories

WINSYSTEMS cables and batteries simplify connection to the EBC-C413.

The following table lists available items.

Item

Part Number

Connection

Description

Cables

CBL-236-G-2-1.5

See “PWR - Power

Connector” on page 23

PWR power connection, DC

harness EBC-TX. Unterminated,

18”

CBL-173-G-1-1.0

See “COM3-4 - COM3 and

COM4 Serial Ports” on

page 25

COM3 and COM4, PCM-COM 4

CBL-247-G-1-1.0

See “MIO - PS/2 Keyboard,

Serial 1/2, and LPT” on

page 26

Multi I/O: primary serial channels

(COM1 and COM2), printer port,

and keyboard

CBL-RST-402-18

See “RST - Reset Connector”

on page 28

Normally open monetary contact

switch, 18”

CBL-PWR-600-14

See “ATXAUX - ATX/Auxiliary

Power Connector” on

page 24

ATX signals for the power button,

5 V standby, and power good

CBL-343-g-1-1-1.375

See “MOUSE - PS/2 Mouse

Connector” on page 28

PS/2 mouse connection to 5 pin,

16.5”

CBL-USB4-000-14

See “USB1 - USB Connector

for Ports 0-3” on page 29.

See “USB2 - USB Connector

for Ports 4-7” on page 30

Pico-Clasp to unterminated

CBL-USB4-001-12

Pico-Clasp to Pico-Clasp

CBL-USB4-002-12

Pico-Clasp to 2 each, 2 x 4, 2 mm

pitch housing

CBL-129-4

See “DIO1 - Digital I/O

Connector with Event Sense”

on page 31
See “DIO2 - Digital I/O

Connector” on page 33

Connect to 48 bidirectional TTL

digital I/O lines (dual-port ram)

CBL-SATA-701-20

See “SATA1 - Serial ATA

Connector” on page 38

Latching signal, 0.5 m

CBL-PWR-117-12

See “SATAPWR - Serial ATA

Power Connector” on

page 38

Power cable to SATA drive

CBL-234-G-1-1-375

See “VGA - Analog VGA

Display Connector” on

page 41

2.0 mm to 15, D-sub (female)

CBL-AUDIO7-102-12

Duo-Clasp. See “AUDIO - HD

Audio Connector” on

page 44

1.25 mm to 3 x 3.5 mm, 12”

CBL-AUDIO7-100-14

1.25 mm, unterminated, 14"

CBL-AUDIO5-102-12

1.25 mm to 6 x 3.5 mm, 12”

CBL-AUDIO2-102-12

1.25 mm to 9 x 3.5 mm, 12”

Batteries BAT-LTC-E-36-16-1

See “BAT - External Battery

Connector” on page 43.

External 3.6 V, 1650 mAH battery

with plug-in connector External

BAT-LTC-E-36-27-1

External 3.6 V, 2700 mAH battery

with plug-in connector

Screws

G527-0000-400

See “MC1 - MiniCard

Connector with PCI-Express

and USB” on page 46
See “MC2 - MiniCard/mSATA

Connector with PCI-Express,

USB, and SATA” on page 47

2 mm

Jumpers

KIT-JMP-G-200

See “Jumpers” on page 51

Jumper Kit (10 jumpers)

Summary of Contents for EBC-C413




















































































Search results

Summary of Contents for EBC-C413

Reviews:

Related manuals for EBC-C413

Brands by name

Popular brands

WinSystems EBC-C413, Product Manual

Search results

Summary of Contents for EBC-C413

Reviews:

Related manuals for EBC-C413

Brands by name

Popular brands