WinSystems EBC-C413 Product Manual Download Page 79

Page: 79 / 83

EBC-C413/Power-on Self-Test (POST) Codes

v1.2

www.winsystems.com

Page 79

DXE Phase

The DXE phase 8-Bit POST code values are shown in the table below.

NOTE The shaded rows in the table indicate the related functions are not from

InsydeH2O (platform dependent).

PEI_WATCHDOG_INIT

Watchdog timer initialization

PEI_MEMORY_INIT

Memory Initialization for Normal boot

PEI_MEMORY_INIT_FOR_CRISIS

Memory Initialization for Crisis Recovery

PEI_MEMORY_INSTALL

Simple Memory test

PEI_TXTPEI

TXT function early initialization

PEI_SWITCH_STACK

Start to use Memory

PEI_MEMORY_CALLBACK

Set cache for physical memory

PEI_ENTER_RECOVERY_MODE

Recovery device initialization

PEI_RECOVERY_MEDIA_FOUND

Found Recovery image

PEI_RECOVERY_MEDIA_NOT_FOUND

Recovery image not found

PEI_RECOVERY_LOAD_FILE_DONE

Load Recovery Image complete

PEI_RECOVERY_START_FLASH

Start Flash BIOS with Recovery image

PEI_ENTER_DXEIPL

Loading BIOS image to RAM

PEI_FINDING_DXE_CORE

Loading DXE core

PEI_GO_TO_DXE_CORE

Enter DXE core

PEI_IFFS_TRANSITION_START

iFFS Transition Start

PEI_IFFS_TRANSITION_END

iFFS Transition End

Value

Functionality Name

Description

Value

Functionality Name

Description

DXE_TCGDXE

TPM initialization in DXE

DXE_SB_SPI_INIT

South bridge SPI initialization

DXE_CF9_RESET

Setup Reset service

DXE_SB_SERIAL_GPIO_INIT

South bridge Serial GPIO initialization

DXE_SMMACCESS

Setup SMM ACCESS service

DXE_NB_INIT

North bridge Middle initialization

DXE_SIO_INIT

Super I/O DXE initialization

DXE_LEGACY_REGION

Set up Legacy Region service

DXE_SB_INIT

South Bridge Middle Initialization

DXE_IDENTIFY_FLASH_DEVICE

Identify Flash device

DXE_FTW_INIT

Fault Tolerant Write verification

DXE_VARIABLE_INIT

Variable Service Initialization

DXE_VARIABLE_INIT_FAIL

Fail to initialize Variable services

DXE_MTC_INIT

MTC Initialization

DXE_CPU_INIT

CPU middle-phase initialization

DXE_MP_CPU_INIT

Multi-processor middle-phase initialization

DXE_SMBUS_INIT

SMBUS Initialization

DXE_SMART_TIMER_INIT

8259 Initialization

DXE_PCRTC_INIT

RTC Initialization

DXE_SATA_INIT

SATA Controller early initialization

DXE_SMM_CONTROLER_INIT

Setup SMM Control service

DXE_LEGACY_INTERRUPT

Setup legacy interrupt services

Summary of Contents for EBC-C413




















































































Search results

Summary of Contents for EBC-C413

Reviews:

Related manuals for EBC-C413

Brands by name

Popular brands

WinSystems EBC-C413, Product Manual

Search results

Summary of Contents for EBC-C413

Reviews:

Related manuals for EBC-C413

Brands by name

Popular brands