WinSystems EBC-C413 Product Manual Download Page 43

Page: 43 / 83

EBC-C413/Configuration

v1.2

www.winsystems.com

Page 43

Layout and Pin Reference

7.12.21 BAT - External Battery Connector

An optional external battery, connected to BAT, supplies the EBC-C413

board with standby power for the real-time clock and CMOS setup RAM.

Extended temperature lithium batteries are available from WINSYSTEMS,

part numbers:

• BAT-LTC-E-36-16-1
• BAT-LTC-E-36-27-1

A power supervisory circuit contains the voltage sensing circuit and an

internal power switch to route the battery or standby voltage to the

circuits selected for backup. The battery automatically switches on when

the VCC of the systems drops below the battery voltage and off when VCC

returns to normal.

Layout and Pin Reference

Additional Information

This connection uses Molex part number 22-11-2032.

Pin

Name

Description

Pin

Name

Description

GND

Ground

Hot

Plug

Detect Hot Plug Detect

ML_Lane

(p) Lane 0 (positive)

CONFIG1

ML_Lane

(n) Lane 0 (negative) 6

CONFIG2

GND

Ground

GND

Ground

ML_Lane

(p) Lane 1 (positive)

ML_Lane

(p)

Lane 3 (positive)

ML_Lane

(n) Lane 1 (negative) 12

ML_Lane

(n)

Lane 3

(negative)

GND

Ground

GND

Ground

ML_Lane

(p) Lane 2 (positive)

AUX_CH

(p)

Auxiliary

Channel

(positive)

ML_Lane

(n) Lane 2 (negative) 18

AUX_CH

(n)

Auxiliary

Channel

(negative)

GND

Ground

DP_PWR

Power for

connector

Pin

Name

Description

No Connect

VBAT (BAT+)

Battery Voltage Input

GND

Ground

Summary of Contents for EBC-C413




















































































Search results

Summary of Contents for EBC-C413

Reviews:

Related manuals for EBC-C413

Brands by name

Popular brands

WinSystems EBC-C413, Product Manual

Search results

Summary of Contents for EBC-C413

Reviews:

Related manuals for EBC-C413

Brands by name

Popular brands