3-2
• Press the
Temperature
button until the de-
sired temperature is indicated.
NOTE: Pressing the
Dryness Level
button will
cause the triple beep, indicating that this option
is not selectable. Also, a dryness level is not
indicated.
The initial time displayed is the actual drying
time. As the cycle runs, the control senses the
dryness of the load, and adjusts the time auto-
matically for the selected dryness level.
• Press and release the
Wrinkle Shield
button
if this option is desired.
• Press the
End Of Cycle Signal
button to set
the volume to the desired level.
• Press and hold the
Hold To Start
button until
the dryer starts (about 1 second).
To use a
Manual Cycle
:
• Rotate the dial to select a
Manual Cycle
.
• Press
More Time
or
Less Time
until the
desired drying time is displayed. Tap
More
Time
or
Less Time
and the time will change
by 1 minute intervals. Press and hold
More
Time
or
Less Time
and the time will change
by 5 minute intervals.
NOTE: The
More Time
or
Less Time
feature
can only be used with
Manual Cycles
.
More
Time
Less
Time
• Press the
Wrinkle Shield
feature button, if
this option is desired.
• Press the
End Of Cycle Signal
button to set
the signal volume to the desired level.
• Press and hold the
Hold To Start
button until
the dryer starts (about 1 second).
Once an
Automatic Cycle
has started, the
Wrinkle Shield
feature, and the
End Of Cycle
Signal
level can be adjusted. Press the
Pause/
Cancel
button twice to stop the dryer and clear
the settings, allowing you to select another
cycle and dryness level.
During a
Manual Cycle
, you can change the
settings for
Time
,
Temperature
, the
Wrinkle
Shield
feature, and the
End of Cycle Signal
functions. Press the
Pause/Cancel
button twice
to stop the dryer and clear the settings, allow-
ing you to select another cycle.
STOPPING THE DRYER
To stop the dryer at any time:
• Press the
Pause/Cancel
button twice.
PAUSING OR RESTARTING
To pause the dryer at anytime:
• Open the door or press the
Pause/Cancel
button once.
To restart the dryer:
• Close the door and press and hold the
Hold
To Start
button until the dryer starts.
NOTE: Drying will continue from where the
cycle was interrupted if you close the door and
press
Start
within 5 minutes. If the cycle is
interrupted for more than 5 minutes, the dryer
will shut off. Select the new cycle settings
before restarting the dryer.
CONTROL LOCKED
This feature allows you to lock your settings to
prevent unintended use of the dryer. You can
also use this feature to prevent unintended
cycle changes during dryer operation.
To enable the
Control Locked
feature:
Press and hold the
End Of Cycle Signal
button
for 3 seconds. The control is locked when a
single beep is heard and the
Control Locked
status light is on.
• When the dryer is off, it is not necessary to
press the
Control On
button before activat-
ing the
Control Locked
feature.
To unlock the
Control Locked
feature:
Press and hold the
End Of Cycle Signal
button
for 3 seconds to turn this feature off.
NOTE: When the dryer is running and
Control
Locked
is on, the dryer can be stopped by
pressing the
Pause/Cancel
button, but cannot
be restarted until the control is unlocked.
Summary of Contents for duet GEW9200L Series
