Whirlpool Cassinetta Repair Manual Line Download Page 71

Page: 71 / 78

Rattling noise?

Possible reason - On old appliances with
ITW electronics:

The capacitors in the main electronic board are
loosing capacity.

Change the main board (follow the description
in the

Service Bulletin 4812 711 40179

, for old

appliances)

Ventilation noise?

Check what fan is responsible of noise (using
the BI test and opening the fridge door - in this
case the evaporator fan will stop).

Compressor fan:

Check if something is in
contact with the blades. If
all OK, replace the fan.

Evaporator fan:

Check if the motor fan
assembly is ok. Be sure
that the blade is
completely inserted in the
motor shaft.

Check also if noise could
be generated by the
vibration transmission
due to some contacts
between shelf and
freezer cover ribs.

Follow the instruction in

Service Bulletin 4812 711
40317

Troubleshooting & Diagnostic:

Noise from the appliance.

Summary of Contents for Cassinetta















































































Search results

Summary of Contents for Cassinetta

Reviews:

Related manuals for Cassinetta

Brands by name

Popular brands

Whirlpool Cassinetta, Repair Manual Line

Search results

Summary of Contents for Cassinetta

Reviews:

Related manuals for Cassinetta

Brands by name

Popular brands